|
|
|
|
|
|
BMW Garage | BMW Meets | Register | Today's Posts | Search |
|
BMW 3-Series (E90 E92) Forum
>
Question re: 6FL kit
|
|
11-24-2021, 02:43 PM | #89 |
Private First Class
7
Rep 100
Posts |
Hello
I need some help,i move from Mulf without USB to Combox,coded but now i need the code of the cable from the Combox to USB port(it will be near the Combox) Thx to someone who will help |
Appreciate
0
|
11-25-2021, 11:33 AM | #92 |
Lieutenant General
1911
Rep 13,103
Posts |
Try looking it up on RealOem.com
There is nothing magic about these cables there are substitutes on ebay and Amazon that have the entire cable and the Pod the plugs into the center console. |
Appreciate
0
|
11-27-2021, 07:15 PM | #94 |
Lieutenant General
1911
Rep 13,103
Posts |
Have you tried following the wiring .
take and ohm meter and measure from the micorphone to the Combox connector . verify each wire. Otherwise you might try so substitute a similar microphone on a short wire directly to the Combox connector.(for trouble shooting purposes.) A microphone only as a + and - and shield wire. https://www.e90post.com/forums/showthread.php?t=1452541 2nd entry is block diagram for combox. Try reading the software file for the Combox and seeing if the settings make sense. https://www.m5board.com/threads/trou...arning.606252/ Last edited by ctuna; 11-27-2021 at 07:38 PM.. |
Appreciate
0
|
11-28-2021, 12:04 PM | #96 |
Lieutenant General
1911
Rep 13,103
Posts |
Did it solve your problem?
Pictures of Mulf on the 2nd link says pin 26 is not used on the Mulf or the Combox. TCU to mulf info in the following link http://www.e90post.com/forums/showthread.php?t=1181654 Clearer combox block diagram in the following link https://www.bimmerfest.com/threads/f...401714&slide=0 Last edited by ctuna; 11-28-2021 at 12:16 PM.. |
Appreciate
0
|
11-28-2021, 04:26 PM | #98 |
Lieutenant General
1911
Rep 13,103
Posts |
Also did you program for the
Combox . A car older than the date the combox was released will not take the programming unless you change the production date long enough to get the programming to take . There is an example of this in the TCU to Mulf link I put up here. You need to trace the wiring to your microphone to be sure you have one. Also the combox you bought cut just be bad. Did you have a working microphone before? |
Appreciate
0
|
11-29-2021, 02:08 AM | #99 | |
Private First Class
7
Rep 100
Posts |
Quote:
Car is 7/2007,need to ask to the man who have programmed me I had Muld 2(no high) and microphone work With Combox i have BT,audio streaming but no one hear me |
|
Appreciate
0
|
11-29-2021, 02:20 PM | #101 |
Private First Class
7
Rep 100
Posts |
|
Appreciate
0
|
11-29-2021, 06:13 PM | #102 |
Lieutenant General
1911
Rep 13,103
Posts |
That means nothing if you can't read the file and look
at the individual parameters you are lost. Looks like you let other people do the work for you and they have never done one. So find someone that has done this near you and can verify all the steps. |
Appreciate
0
|
11-29-2021, 06:58 PM | #103 |
Private First Class
7
Rep 100
Posts |
I think the same...
|
Appreciate
0
|
Bookmarks |
|
|