CAN code 474C

geko29 · 03-03-2014, 05:45 PM

I got a limp today from running too hard too soon (JBD at 100%). After clearing codes, I still have one--474C. I can't clear it, but I don't know what it means. There aren't any OBD codes stored, which I've verified with my Actron.

My "No start in XXX miles" warning is up, is that what this code means? I suppose I could re-check after adding some AdBlue, but I didn't know if maybe somebody had run into this before.

Brad335d · 03-03-2014, 07:18 PM

As far as I know all DTC codes (Global and OEM) are 4 characters long not including the prefix i.e. P or U. You have a five character code listed here. Check the code again and verify it. Also What type of actron scanner do you have. Most of these are not reliable when scanning for an OEM code. You'll need something with OEM capability like a dealer or a good independent shop has. Just so you know I looked all though my manufacturer specific codes and found nothing over 4 characters long or with any combinations I could assume you meant to type. Sometimes when a scanner has an unknown OEM code it will display it with an incorrect Code ID.

geko29 · 03-03-2014, 07:59 PM

Sorry I guess the changes didn't save when I edited the post. It's 474C. That code I get from the CAN tool that came with the JBD. It uses the speedo as a display, so cycles through 4-7-4-12, with the 12 representing C. I only plugged in the Actron to verify my suspicion that it was NOT an OBD code.

135i_vs_ · 03-04-2014, 07:07 AM

474C should be for the Exhaust Fluid warning "No Start XXX".
Add some Urea, and it will clear itself.

geko29 · 03-04-2014, 08:53 AM

Quote:

Originally Posted by 135i_vs_

474C should be for the Exhaust Fluid warning "No Start XXX".
Add some Urea, and it will clear itself.

Awesome, that's what I was hoping. I'm going to add a half gallon next week when it gets down to the 2-300mi range. Currently just under 600, with 1600 till my next oil change. Already added a gallon last month, hopefully this'll be enough to get me to the dealer refill.

I'll report back to confirm that it goes away when the indicator's gone.

geko29 · 03-26-2014, 08:29 AM

Hey guys, I forgot to report back last week. When I added 1.5 gallons of DEF and drove around until the "no start" cleared, this code went away also.

03-03-2014, 05:45 PM	#1
geko29 Major 1565 Rep 1,422 Posts Drives: 2023 M3 6MT Join Date: May 2012 Location: Illinois, USA iTrader: (2)	CAN code 474C I got a limp today from running too hard too soon (JBD at 100%). After clearing codes, I still have one--474C. I can't clear it, but I don't know what it means. There aren't any OBD codes stored, which I've verified with my Actron. My "No start in XXX miles" warning is up, is that what this code means? I suppose I could re-check after adding some AdBlue, but I didn't know if maybe somebody had run into this before. __________________ Last edited by geko29; 03-03-2014 at 07:59 PM..
	Appreciate 0 Tweet Quote

03-03-2014, 07:18 PM	#2
Brad335d Oil Burner 26 Rep 231 Posts Drives: 2011 BMW 335d Join Date: Nov 2009 Location: Atlanta, GA iTrader: (0) Garage List 2014 Volvo XC60 T6 AWD [0.00] 2011 BMW 335d [0.00] 2007 Ford Shelby GT500 [0.00]	As far as I know all DTC codes (Global and OEM) are 4 characters long not including the prefix i.e. P or U. You have a five character code listed here. Check the code again and verify it. Also What type of actron scanner do you have. Most of these are not reliable when scanning for an OEM code. You'll need something with OEM capability like a dealer or a good independent shop has. Just so you know I looked all though my manufacturer specific codes and found nothing over 4 characters long or with any combinations I could assume you meant to type. Sometimes when a scanner has an unknown OEM code it will display it with an incorrect Code ID. __________________ '11 BMW 335d Sport -JBD '07 Shelby GT500 -Not Stock
	Appreciate 0 Quote

03-03-2014, 07:59 PM	#3
geko29 Major 1565 Rep 1,422 Posts Drives: 2023 M3 6MT Join Date: May 2012 Location: Illinois, USA iTrader: (2)	Sorry I guess the changes didn't save when I edited the post. It's 474C. That code I get from the CAN tool that came with the JBD. It uses the speedo as a display, so cycles through 4-7-4-12, with the 12 representing C. I only plugged in the Actron to verify my suspicion that it was NOT an OBD code. __________________
	Appreciate 0 Quote

03-04-2014, 07:07 AM	#4
135i_vs_ Captain 72 Rep 697 Posts Drives: M5, 135i, 335d, F10 550xi Join Date: Sep 2011 Location: CT iTrader: (0)	474C should be for the Exhaust Fluid warning "No Start XXX". Add some Urea, and it will clear itself.
	Appreciate 0 Quote

03-26-2014, 08:29 AM	#6
geko29 Major 1565 Rep 1,422 Posts Drives: 2023 M3 6MT Join Date: May 2012 Location: Illinois, USA iTrader: (2)	Hey guys, I forgot to report back last week. When I added 1.5 gallons of DEF and drove around until the "no start" cleared, this code went away also. __________________
	Appreciate 0 Quote