|
|
|
|
|
|
BMW Garage | BMW Meets | Register | Search | Today's Posts | Mark Forums Read |
|
BMW 3-Series (E90 E92) Forum
>
DIY: IHKA replacement (Down the squeaky dash rabbit-hole.)
|
|
10-31-2024, 12:35 PM | #23 | ||
Neo-Luddite
3469
Rep 1,741
Posts
Drives: '06 325i, 330i 6MT RWD Sport
Join Date: Nov 2020
Location: NJ
|
Quote:
Quote:
|
||
Appreciate
1
Mike K398.00 |
10-31-2024, 12:38 PM | #24 | |
Neo-Luddite
3469
Rep 1,741
Posts
Drives: '06 325i, 330i 6MT RWD Sport
Join Date: Nov 2020
Location: NJ
|
Quote:
|
|
Appreciate
0
|
10-31-2024, 08:03 PM | #25 |
Second Lieutenant
382
Rep 236
Posts |
Thanks for taking us along on this project and sharing pictures! Been through my fair share of interior noises on my ’06 with sport package. Noise wise, the sport suspension can be harsh, but I’ve had success in getting the interior generally noise free.
Some indispensable items in my toolbox: DuPont Krytox GPL 205 0.5oz DuPont Krytox GLP 105 with needle nose 0.5oz BMW Gummi-Pflege The 205 is more of a grease and the 105 is more of a liquid where the needle nose applicator is great. If you shop around, you can get a good price on the 0.5oz size and they’ll last years. The spec sheets indicate they are designed for interiors, and a few car manufacturers spec them in their TSBs when dealing with interior noises (I guess if it works for Cadillac…) Handful of areas I was able to correct in case it's helpful -Plastic Trim panel on top/center of dashboard (where the center speaker goes on Logic7). Mine disintegrated when I tried to remove it, but I replaced it with new and used GPL205 around the perimeter and where the clips lock in. -Same for the small side defroster vents on the top of the dashboard. They might squeak, but you can get GPL105 in there without removing them and it will fix it. -All Air Vents. The dial to open/close the vents can slightly disintegrate with age and there’s a spring in there that might rattle as a result. BMW went through many iterations of the vents, I replaced with the latest LCI version. -Air Vent Foam Tape. The foam tape around the vents (when they are pulled out) is mostly disintegrated at this point, it causes the plastics to rub together. I used MD building Products 02055 in 3/16 x 3/8” as BMW doesn’t sell the foam tape separate to the vents. -Center console wood. For 2006, BMW had a TSB, they recommend installing a piece of flocked tape (the Tesa tape with velour works) only on the passenger side of the wood where it rubs against the plastic for the lower part of the dash. -Wood Trim. Replaced the clips for a tighter fit and some 205 on where the wood will rub against the dash/door plastics. Fun fact, on my 2006 they used fabric tape on the back where the AC vents lock into the wood trim. It’s no longer there on the LCI models. -Door Trim. Ended up replacing the clips for a tighter fit, especially the ones for the wood trim and some 205 on areas that might rub. I started with one door and it went downhill from there with replacing everything, but it was worth it. -Door lock pegs, I’ve had these rub against the ring on the door panel and create a buzz. 105 on them and it never came back. -Door Creaking. Of course, Gummi all weatherstripping. But 205 on the flocked part of the upper weatherstripping that rubs against the shadowline always worked for me. -Steering Wheel Stalks. Had the button on the cruise control make a spring buzz, was able to get 105 in there and so far so good. Originally it sounded like it was coming from the center of the dash (same for most of these noises). -Wiring Hold Down Clips. I replaced any wiring hold down clips (like the ones inside the door panel) and used Tesa 51036 tape to replace any worn tape. Small change, but really helped. -Seats/Leather Rubbing. I do a full Leatherique treatment which helps with where the leather rubs, but you can also use some 205 in certain areas, particularly where the plastic seat button trim rubs against the leather. On the LCI, BMW moved to using vinyl and velour in certain areas that may rub, like the back seats where the seat belt buckles are. Assume it was partly cost cutting, but also to help with noise. I’ve also noticed the flappers on the HVAC might rattle once in a blue moon. I’m not sure if it’s due to the stepper motors aging, insulation on the flaps missing or something else. I solve that one by adjusting the temperature/vents and it goes away. Looking forward to seeing how your HVAC rebuild progresses! |
Appreciate
5
|
11-01-2024, 07:49 PM | #26 |
Neo-Luddite
3469
Rep 1,741
Posts
Drives: '06 325i, 330i 6MT RWD Sport
Join Date: Nov 2020
Location: NJ
|
Thanks Cal122 I'm gonna look into that Krytox stuff. More weapons in the arsenal is always a good thing. I will try to pay attn to all those spots you mentioned as I put it back together
|
Appreciate
2
StradaRedlands6580.00 Cal122382.00 |
11-01-2024, 08:10 PM | #27 |
Neo-Luddite
3469
Rep 1,741
Posts
Drives: '06 325i, 330i 6MT RWD Sport
Join Date: Nov 2020
Location: NJ
|
Well not 100% off topic anyway. I had a day off to think on this and got as straight as possible in my mind the steps I had to take to move this project along.
This was my day off. This is not a political post, my dog is non-partisan and would vote for whoever is giving her treats or toys or scritchies. She sniffed this out on Dog Beach as we were strolling thru the sand.... |
Appreciate
2
StradaRedlands6580.00 Efthreeoh19329.00 |
11-01-2024, 08:37 PM | #28 |
Neo-Luddite
3469
Rep 1,741
Posts
Drives: '06 325i, 330i 6MT RWD Sport
Join Date: Nov 2020
Location: NJ
|
NGL, this job isn't real fun. It's like doing a 3D jigsaw puzzle while playing Twister. I got everything from the old box transferred which is the wiring harness, 8 flap motors, 3 temp sensors, the blower housing and the aluminum piping from the heater core. The old heater core looked in good condition at least externally, but for $60 I wasn't gonna skip replacing it. The evaporator makes you take it halfway apart to install but after a little tussle got that installed. I had to leave 2 motors dangling because I couldn't get them to line up with the flap drive shaft.
I put the unit back roughly in place and the cage loosely around it with a couple nuts holding it roughly in place then re-connected the unit, the key slot, start button, headlight switch, cluster and temp control panel. From there I was able to reconnect the battery and turn it on to accessory position. I used Protools to actuate the motors until I got them to a position I could get them on the drive shafts, then a 5.5mm ignition wrench to tighten the screws. Now I can finally start putting it back together |
Appreciate
1
StradaRedlands6580.00 |
11-02-2024, 08:01 AM | #29 |
General
19329
Rep 19,786
Posts |
Same with the E30.
__________________
A manual transmission can be set to "comfort", "sport", and "track" modes simply by the technique and speed at which you shift it; it doesn't need "modes", modes are for manumatics that try to behave like a real 3-pedal manual transmission. If you can money-shift it, it's a manual transmission. "Yeah, but NO ONE puts an automatic trans shift knob on a manual transmission."
|
Appreciate
1
3PedalJake3469.00 |
11-03-2024, 02:59 PM | #30 |
Neo-Luddite
3469
Rep 1,741
Posts
Drives: '06 325i, 330i 6MT RWD Sport
Join Date: Nov 2020
Location: NJ
|
Tip of the day for those unfortunate enough to find themselves in the middle of this task. When you go to reinstall the HVAC cabinet, the main mounting "nut"/"ferrule" has plastic prongs before the threads start, you have to push the bolt in HARD to get it past these prongs. Don't lean in there to one of the most inaccessible spots on the car, the firewall directly behind the CCV hose, desperately spinning the bolt with your fingertips for an hour trying to get the threads to start like I did. I finally had a peek at the old box and figured it out, after that it went in fine.
Got cabinet, the cage and the new heater hoses and AC o-rings installed in the engine compartment and got that buttoned up. I found a cabin filter housing with the wire loom clips not broken off cheap on ebay so got that in place too. Have to stop here because waiting on new foam gaskets for the vents where they meet the dash, should be at the local stealer tomorrow. |
Appreciate
3
|
11-05-2024, 10:44 AM | #31 |
Neo-Luddite
3469
Rep 1,741
Posts
Drives: '06 325i, 330i 6MT RWD Sport
Join Date: Nov 2020
Location: NJ
|
Got my gasket set from BMW, PN: 64116950976. Cal122 I got some of the magic lube you suggested, found a $10 set on Amazon that included a small quantity of the oil and grease along with a little paintbrush. I also got a set of the needle tip applicator bottles. Today I'll go over all the dash mount points and contact areas and apply a drop or smear of the lube.
This project was so unexpected and so challenging that it overcame my natural OCD to remove every spec of rust, so on the cage I just sanded it down with a Scotchbrite pad and wiped it good with anti-corrosion spray. Hoping I can get t all back together today... wish me luck bimmer bros. |
Appreciate
3
|
11-05-2024, 11:18 PM | #32 |
Brigadier General
6580
Rep 3,922
Posts
Drives: 2006 BMW 330i MT
Join Date: Dec 2021
Location: SoCal
iTrader: (3)
Garage List 2006 BMW 330i [8.45]
2009 BMW 328i Touri ... [8.00] 2013 BMW X5 35i [7.80] 2011 BMW 528i [8.70] 2006 Mazda3 [5.50] |
Everything's coming up Milhouse!
I've found WD-40 specialty products to be pretty good stuff BTW. Their namesake product is fine for what it was intended to do as well. Last edited by StradaRedlands; 11-06-2024 at 12:49 AM.. |
Appreciate
2
3PedalJake3469.00 Daaaaaaaan98.50 |
11-06-2024, 12:05 AM | #33 |
Neo-Luddite
3469
Rep 1,741
Posts
Drives: '06 325i, 330i 6MT RWD Sport
Join Date: Nov 2020
Location: NJ
|
Well finally got it back together. It all works and was getting ready to celebrate, but seems I broke my passenger seat occupancy sensor while I was doing Twister in there Have code 93c3. This is the project that keeps on giving.
Millhouse indeed lol |
Appreciate
4
|
11-06-2024, 11:34 AM | #34 |
Major
442
Rep 1,129
Posts |
Regarding squeeky, sometimes it is a metal crack or a cracked weld. Been there, done that, but not on a BMW!
You might try and localize with a sound level meter or an app on you phone. |
Appreciate
2
StradaRedlands6580.00 3PedalJake3469.00 |
11-06-2024, 04:58 PM | #35 |
Second Lieutenant
382
Rep 223
Posts |
Holy Cow! It's done. I hope it all went well as far as the noise being gone.
|
Appreciate
2
StradaRedlands6580.00 3PedalJake3469.00 |
11-07-2024, 11:15 PM | #36 | ||
Neo-Luddite
3469
Rep 1,741
Posts
Drives: '06 325i, 330i 6MT RWD Sport
Join Date: Nov 2020
Location: NJ
|
Quote:
Quote:
I kneeled on the passenger seat and broke the occupancy sensor while I was playing twister with the dash. Grrrrrrrrr, I just put those new leather seats in there a couple weeks ago, couldn't have broke the old manual seat. The BMW approved repair is to replace the foam on the seat bottom that includes the sensor and the heating element, for over $800 just for the part. I could put a emulator on there but that would gnaw at my OCD. For now I put the old manual vinyl seat back in, that has heat that's all Mrs. 3P cares about. In the winter when project list is shorter I'll swap the cushion from the manual seat. Now the saddest part of the saga, the squeak is still there same as before . At least it wasn't all in vain, the HVAC box was toast it needed to be replaced but now I gotta hunt elsewhere for the squeak. Tomorrow it goes back on the Quickjack to get the sway bushings lubed and anything else I can check like shields and stuff underneath, I think I ruled out the dash time to cast a wider net. |
||
Appreciate
2
StradaRedlands6580.00 Cal122382.00 |
11-07-2024, 11:33 PM | #37 |
Brigadier General
6580
Rep 3,922
Posts
Drives: 2006 BMW 330i MT
Join Date: Dec 2021
Location: SoCal
iTrader: (3)
Garage List 2006 BMW 330i [8.45]
2009 BMW 328i Touri ... [8.00] 2013 BMW X5 35i [7.80] 2011 BMW 528i [8.70] 2006 Mazda3 [5.50] |
|
Appreciate
1
3PedalJake3469.00 |
11-07-2024, 11:36 PM | #38 |
Neo-Luddite
3469
Rep 1,741
Posts
Drives: '06 325i, 330i 6MT RWD Sport
Join Date: Nov 2020
Location: NJ
|
|
Appreciate
3
|
11-09-2024, 01:58 PM | #39 |
Second Lieutenant
157
Rep 275
Posts |
Why not take dash apart one detail before each journey.
This way you eventually find what is causing it. (in my case the long piece that is holding the hazard lights and middle/right vent was causing some noises). I just added some foam where i tough it makes contact and it no longer makes sounds. Have you tried driving without dash in? Does it still make noise? maybe it's something on the other side of firewall. |
Appreciate
2
3PedalJake3469.00 StradaRedlands6580.00 |
11-09-2024, 02:13 PM | #40 | |
Neo-Luddite
3469
Rep 1,741
Posts
Drives: '06 325i, 330i 6MT RWD Sport
Join Date: Nov 2020
Location: NJ
|
Quote:
|
|
Appreciate
0
|
11-09-2024, 02:32 PM | #41 |
Second Lieutenant
382
Rep 236
Posts |
How about the cowl piece that's under the windshield wipers, where the rubber is pushing against the windshield? I had more of a ticking noise than a squeak during cold weather, so I took apart the cowl and in addition to a ton of dirt buildup, found the rubber on the backside that pushes against the windshield was really dry and the bottom of the windshield had some rough etching from rain water. I figured if the door seals can make a creaking noise in the cabin, the windshield has to be the same. Cleaned everything really well, soaked the rubber trim in Gummi and then lubed up all of the parts that rub against the windshield.
|
Appreciate
2
Mike K398.00 3PedalJake3469.00 |
11-10-2024, 05:56 PM | #42 |
Major
442
Rep 1,129
Posts |
I also hate squeeks. I once repaired squeeks on collegues Mustang, on a late night trip back from the airport, by balling and wetting pieces of tissue and forcing them into appropriate spots. He was very appreciative.
Would 1"x2" wood strips on the road be enough to force the squeek. |
Appreciate
1
3PedalJake3469.00 |
11-10-2024, 05:59 PM | #43 |
Major
442
Rep 1,129
Posts |
A dropper with plastic safe silicone oil can be used for troubleshooting, as sprays can get too messy.
|
Appreciate
2
StradaRedlands6580.00 3PedalJake3469.00 |
11-15-2024, 06:02 AM | #44 |
New Member
9
Rep 25
Posts |
Found the problem
In my case IT WAS THE CCC HEADUNIT more precisely it was this plastic trim on the CCC head unit when I put pressure on it the creaking disappeared instantly when I stopped holding it the creaking reappeared.
__________________
SS
|
Appreciate
2
3PedalJake3469.00 StradaRedlands6580.00 |
Bookmarks |
Thread Tools | Search this Thread |
|
|