|
|
|
|
|
|
BMW Garage | BMW Meets | Register | Search | Today's Posts | Mark Forums Read |
|
BMW 3-Series (E90 E92) Forum
>
DIY: Replacing the fuel breather pipe
|
|
04-17-2020, 01:26 AM | #23 | |||||
Colonel
529
Rep 2,505
Posts |
Quote:
You won't be able to see the damaged area. The damage is almost always on the side next to the tank (under the rear seat). Unless you have visible fuel leaking out when the tank is full, I wouldn't worry. |
|||||
Appreciate
0
|
05-08-2020, 08:30 AM | #25 | |
Registered
0
Rep 3
Posts |
Quote:
Edit: now sorted. 44mm hole on the side to feed the hose through. On my 06 330i saloon there was no chance of taking the hose out through the wheel well or feeding the new one in. The fuel tank connector with the white tab is just too big. A 44mm hole was barely enough. Anyway a big thanks for sharing more success with the "drill some holes" method. I'm not sure I'd have tried without that. Looking forward to filling the tank up to the top! Last edited by JonathanC; 05-08-2020 at 04:28 PM.. |
|
Appreciate
0
|
03-16-2022, 06:27 PM | #26 |
New Member
6
Rep 14
Posts |
i finished this job, i drilled a 44mm hole on the side as people above, i could have gotten away with a smaller hole but bigger hole makes the repair easier.. The pipe can be inserted from the wheel arch side. I recommend using an oil change latex glove so u dont push dirt in the pipe. Always buy the protection tube too ( 16124390434 ) if you replace the pipe ( 16126765748 ). For the clip i have removed from the bottom i needed a thin flat head screw driver. It is easier to remove the top part first. The top part i pressed to unclip but it needed to be twisted too. then you can twist the whole pipe to adjust the lower clip so u can remove it easier. After all this i found out my old pipe was not the problem. it might be the pump too. check first the it is actually the pipe. My leak is from from the nipple connection itself, it looks like someone changed the pipe but yanked the nipple and made a leak in its seal or the design is very bad, as the nipple is set to an angle and the pipe pushes against the chassis and the fuel tank, over time the nipple connection with the fuel tank fails and the pipe gets cut. i will try glazing with the soldering iron and cover with POXILINA for additional sealing strength.
For rust and fuel protection i recommend grunding, painting and acrylic clear coat. I managed to find on ebay 43-46mm grommets to cap off the holes. After resolving the issue, it turn out the problem for slicing the pipe, caused the nipple seal to crack at the connection with the fuel tank. Its the angle that the connection comes at. it was half broken leaking fuel from there. The fuel tank vonnection was probably designed by someone withouth a hole sense if you know what i mean. It looks like the fuel tank is made of usual polyethilene and nothing sticks to it. I repaired it with soldering iron where i could reach and a screwdriver heated with a blow torch in harder to access areas. The fuel tank might have a 3mm thickness, i did not go beyond 1mm to get a good bond. Last edited by XCT; 04-04-2022 at 02:56 PM.. Reason: update |
Appreciate
0
|
10-02-2022, 06:27 PM | #27 |
New Member
6
Rep 14
Posts |
it failed again,
cracked in the same spot after driving on some touges with the reservoir full. the permanent solution seems to make the breather hose hole larger and more to the right as it constantly presses on that plastic fitting from the reservoir. |
Appreciate
0
|
10-27-2022, 03:25 PM | #29 |
New Member
6
Rep 14
Posts |
for the interior, the bench has 2 clips near the front of the bench, you just pull on it, the side door trim has 4 clips, you should be able to unclip them by bending the trim a bit and sliding, for the exterior you only have to remove the wheel and clips for the wheel arch to be able to get it out of the way.
as for the update i bent the tube with a heatgun, checked the bend with water to see if it has holes and hope for the best Last edited by XCT; 10-27-2022 at 03:30 PM.. |
Appreciate
0
|
Bookmarks |
Thread Tools | Search this Thread |
|
|