[tnxgalaxy]

Hi everyone,

First, some background: I drove an E36 coupe 323i for 7 years and recently I bought a E60 520d recently (need a family car) as well as an ICOM NEXT (genuine) that I share with my dad for diagnostics and retrofits.
Using WinKfp 5.3.1 and ediabas 7.3.0, I managed to upgrade all the modules that Ista-P (v61) did not manage to upgrade (EKP, RLS, EC, KBM) with the exception of the DME/DDE.
When trying to programme the DDE, Ista-P gives this error:
Global.VehiculeCommunication.CoAPI.2020 - (CoAPI) - control module not responding
ECU old: 7800770 ECU new: 7811742

WinKfp in REMOTE mode gives this error:
Code 9000 Level PABD: Debug 09DDE604, DUAGNOSE_MODE (ECUPM): ERROR_ECU_CONDITIONS_NOT_CORRECT_OR_REQUEST_SEQUEN CE_ERROR.

I found suggestions online to use the REMOTE:MOST_ASYNC_ab625
when I do, I get this error:
Code: 2000 Level:Error : Error in EDIABAS or in ECU description file (SGBD) IFH-0004: Error in interface command 09DDE604

I'm not sure what to try next, any suggestion would be more than welcome!

Thanks!

TNXgalaxy

[Sensible_]

Originally Posted by tnxgalaxy

Hi everyone,

First, some background: I drove an E36 coupe 323i for 7 years and recently I bought a E60 520d recently (need a family car) as well as an ICOM NEXT (genuine) that I share with my dad for diagnostics and retrofits.
Using WinKfp 5.3.1 and ediabas 7.3.0, I managed to upgrade all the modules that Ista-P (v61) did not manage to upgrade (EKP, RLS, EC, KBM) with the exception of the DME/DDE.
When trying to programme the DDE, Ista-P gives this error:
Global.VehiculeCommunication.CoAPI.2020 - (CoAPI) - control module not responding
ECU old: 7800770 ECU new: 7811742

WinKfp in REMOTE mode gives this error:
Code 9000 Level PABD: Debug 09DDE604, DUAGNOSE_MODE (ECUPM): ERROR_ECU_CONDITIONS_NOT_CORRECT_OR_REQUEST_SEQUEN CE_ERROR.

I found suggestions online to use the REMOTE:MOST_ASYNC_ab625
when I do, I get this error:
Code: 2000 Level:Error : Error in EDIABAS or in ECU description file (SGBD) IFH-0004: Error in interface command 09DDE604

I'm not sure what to try next, any suggestion would be more than welcome!

Thanks!

TNXgalaxy

You don't flash DDE/DME with MOST_ASYNC_ab625.

That's for ICOM B and modules on MOST bus. You'll need REMOTE: DiagBus

Use Easyconnect utility which will auto config your ediabas.ini

[tnxgalaxy]

thank you very much for the tip!
however as said previously, even in REMOTE mode I get an error. Could that be because the module is in a particular state and needs to be switched to an other state first?

Thanks for the help

[Levanime]

Do you have ignition on?

[tnxgalaxy]

Yes, I tried with ignition on, and I had a running E36 attached to generate power.
Also, my DDE has the following ZB No: 7800770, and as I could not find it using 'find ZUSB' in WinKfp, had to use 'update ZUBS' and select DDE604, which it is according to realoem:
http://www.realoem.com/bmw/enUS/part...&mg=&q=7800770

[Levanime]

PM me ur teamviewr

[tnxgalaxy]

thanks for the proposition, unfortunately due to the time difference (it's 10pm here in Ireland right now), and the fact that I cannot access easily to the internet from where the car is, I'm afraid that will not be possible that way.

I have taken a couple of photos of my attempts, here is a picture of the error output I'm getting from WinKfp:
https://www.dropbox.com/s/wkhdicin7w...57.20.jpg?dl=0

and this is what inpa tells me about the modules:
https://www.dropbox.com/s/lf21abxh1o...36.55.jpg?dl=0

[Sensible_]

Using winkfp are you selecting comfort mode and updating zusb? Or are you manually choosing the zusb that ISTA-P offered?

[tnxgalaxy]

When using WinKfp, I select comfort mode and updating zusb, as the ZUSB number is not found through 'enter ZUSB'.

Also this is the error output and new ZUSB suggestion from ista-p in case it helps:
https://www.dropbox.com/s/9fxyalwvpu...19.17.jpg?dl=0

[Sensible_]

Have you read the fault memory with ISTA-D? Anything interesting?

[tnxgalaxy]

the only fault I have is with the glow plug #4 but so far the car seems to be working normally.

[Sensible_]

Ok, with tool32 can you try running the job:

authentisierung_zufallszahl_lesen

For your DDE prg.

[tnxgalaxy]

thanks! I will try that and will let you know how it goes.

[otto_rockett]

trying to get the process started for a e63 dme im completely lost i have all the tools and programs needed anyone got some tips for the new guy..

[Sensible_]

Originally Posted by otto_rockett

trying to get the process started for a e63 dme im completely lost i have all the tools and programs needed anyone got some tips for the new guy..

What process? What do you want to do? Are you updating? Retrofitting? We need to know your goal...