[101Duck]

So ex tropical cyclone debbie fucked my car up.

And as a result it's getting parted. All parts have done less than 4000km. Some haven't done 500.


Custom RHD exhaust manifold and Garrett 3884 -67mm
Turbosmart wastegate
hot side Intercooler piping
Dump pipe (will need modifying slightly to fit other cars, any decent fab shop can achieve this)
Billet hardware for all braided water and oil lines
Billet block and silicone hose for water pump hose
near new o2 sensors
silicone joiners

Custom 8.5" stepped intercooler

Forward facing plenum with port injection
Tial BOV
4 bar map sensor
cold side intercooler piping
80lb shorty injectors
fuel lines and adaptors to suit PI kit
brackets for coolant res relocation

m4 coilpacks
r35 gtr spark plugs new unused

rb billet pcv

JB4 and AIC6 controller

fuelit stage 3 fuel pump

full 3.5" exhaust with twin mufflers (suit e9x series)

whole setup, bolt onto your car and make genuine 700hp at the wheels. (made 660hp at 28psi on my car through a 4000rpm stall convertor and powerglide trans)

$10000 (could possibly seperate if people are interested. but it's a proven setup which comes with everything)



Powerglide swap suit E9x/E8x

Built powerglide transmission, freshly overhauled, not even 500km street use since. upgraded clutches, kevlar bands, extended sump, transbrake valve body etc.
Custom powerglide to N54 adaptor
Custom 4000rpm stall convertor suit N54 and powerglide combo
tailshaft suit E9x chassis
gearbox mount suit e9x (may suit e8x)
TCI outlaw shifter with billet trans brake button mount.
PWR transmission cooler with teflon braided lines
wiring to suit powerglide swap (only 4 wires that are hooked up from memory)
will assist in coding to make it run without any warning lights as it did in my car.

$7500


Seibon carbon LCI e90 bootlid painted BSM

$900




17x4.5 JMS wheels and 15x8 wheels suit 5x120 with radial front tires and 275 et slicks (fairly worn) painted gloss black. Great drag setup.

$1200



Carbon pre LCI bonnet e90/e91 painted BSM with brand new bmw badge and gloss black grills.

$600


All other parts for sale if requested. small rear brake swap for 15's, headlights, panels, interior bits, modules, 3.46 large case bolted diff with locked centre (perfect for LSD install) axles etc.

all available, located brisbane, happy to courier.

PM or reply here.
thank you

duck

[Mayuri Krab]

Odd request, but are you willing to sell/part out the plastic white cover (I can see it on your 1st pic of the engine bay) for the DME enclosure box along with the 4 locking slider/clips?

Have one on order from the UK but I rather get it ASAP than leaving the car in garage for 4 weeks waiting for it to arrive... LOL

[Aus335iguy]

Originally Posted by 101Duck

So ex tropical cyclone debbie fucked my car up.

And as a result it's getting parted. All parts have done less than 4000km. Some haven't done 500.


Custom RHD exhaust manifold and Garrett 3884 -67mm
Turbosmart wastegate
hot side Intercooler piping
Dump pipe (will need modifying slightly to fit other cars, any decent fab shop can achieve this)
Billet hardware for all braided water and oil lines
Billet block and silicone hose for water pump hose
near new o2 sensors
silicone joiners

Custom 8.5" stepped intercooler

Forward facing plenum with port injection
Tial BOV
4 bar map sensor
cold side intercooler piping
80lb shorty injectors
fuel lines and adaptors to suit PI kit
brackets for coolant res relocation

m4 coilpacks
r35 gtr spark plugs new unused

rb billet pcv

JB4 and AIC6 controller

fuelit stage 3 fuel pump

full 3.5" exhaust with twin mufflers (suit e9x series)

whole setup, bolt onto your car and make genuine 700hp at the wheels. (made 660hp at 28psi on my car through a 4000rpm stall convertor and powerglide trans)

$10000 (could possibly seperate if people are interested. but it's a proven setup which comes with everything)



Powerglide swap suit E9x/E8x

Built powerglide transmission, freshly overhauled, not even 500km street use since. upgraded clutches, kevlar bands, extended sump, transbrake valve body etc.
Custom powerglide to N54 adaptor
Custom 4000rpm stall convertor suit N54 and powerglide combo
tailshaft suit E9x chassis
gearbox mount suit e9x (may suit e8x)
TCI outlaw shifter with billet trans brake button mount.
PWR transmission cooler with teflon braided lines
wiring to suit powerglide swap (only 4 wires that are hooked up from memory)
will assist in coding to make it run without any warning lights as it did in my car.

$7500


Seibon carbon LCI e90 bootlid painted BSM

$900




17x4.5 JMS wheels and 15x8 wheels suit 5x120 with radial front tires and 275 et slicks (fairly worn) painted gloss black. Great drag setup.

$1200



Carbon pre LCI bonnet e90/e91 painted BSM with brand new bmw badge and gloss black grills.

$600


All other parts for sale if requested. small rear brake swap for 15's, headlights, panels, interior bits, modules, 3.46 large case bolted diff with locked centre (perfect for LSD install) axles etc.

all available, located brisbane, happy to courier.

PM or reply here.
thank you

duck

Looks at Socket

[Vince1219]

Originally Posted by 101Duck

So ex tropical cyclone debbie fucked my car up.

And as a result it's getting parted. All parts have done less than 4000km. Some haven't done 500.


Custom RHD exhaust manifold and Garrett 3884 -67mm
Turbosmart wastegate
hot side Intercooler piping
Dump pipe (will need modifying slightly to fit other cars, any decent fab shop can achieve this)
Billet hardware for all braided water and oil lines
Billet block and silicone hose for water pump hose
near new o2 sensors
silicone joiners

Custom 8.5" stepped intercooler

Forward facing plenum with port injection
Tial BOV
4 bar map sensor
cold side intercooler piping
80lb shorty injectors
fuel lines and adaptors to suit PI kit
brackets for coolant res relocation

m4 coilpacks
r35 gtr spark plugs new unused

rb billet pcv

JB4 and AIC6 controller

fuelit stage 3 fuel pump

full 3.5" exhaust with twin mufflers (suit e9x series)

whole setup, bolt onto your car and make genuine 700hp at the wheels. (made 660hp at 28psi on my car through a 4000rpm stall convertor and powerglide trans)

$10000 (could possibly seperate if people are interested. but it's a proven setup which comes with everything)



Powerglide swap suit E9x/E8x

Built powerglide transmission, freshly overhauled, not even 500km street use since. upgraded clutches, kevlar bands, extended sump, transbrake valve body etc.
Custom powerglide to N54 adaptor
Custom 4000rpm stall convertor suit N54 and powerglide combo
tailshaft suit E9x chassis
gearbox mount suit e9x (may suit e8x)
TCI outlaw shifter with billet trans brake button mount.
PWR transmission cooler with teflon braided lines
wiring to suit powerglide swap (only 4 wires that are hooked up from memory)
will assist in coding to make it run without any warning lights as it did in my car.

$7500


Seibon carbon LCI e90 bootlid painted BSM

$900




17x4.5 JMS wheels and 15x8 wheels suit 5x120 with radial front tires and 275 et slicks (fairly worn) painted gloss black. Great drag setup.

$1200



Carbon pre LCI bonnet e90/e91 painted BSM with brand new bmw badge and gloss black grills.

$600


All other parts for sale if requested. small rear brake swap for 15's, headlights, panels, interior bits, modules, 3.46 large case bolted diff with locked centre (perfect for LSD install) axles etc.

all available, located brisbane, happy to courier.

PM or reply here.
thank you

duck

Starter

[101Duck]

Originally Posted by Mayuri Krab

Odd request, but are you willing to sell/part out the plastic white cover (I can see it on your 1st pic of the engine bay) for the DME enclosure box along with the 4 locking slider/clips?

Have one on order from the UK but I rather get it ASAP than leaving the car in garage for 4 weeks waiting for it to arrive... LOL

Yeah no drama. I have a spare one already anyway. If not two.

[kookie]

Sorry to hear. Debbie was a wild one.

Good luck with the sale. 9second setup right there.

[Aus335iguy]

Originally Posted by kookie

Sorry to hear. Debbie was a wild one.

Good luck with the sale. 9second setup right there.

A cheap one at that....

[101Duck]

Happy to sell the car complete. It still runs and drives. Cant be registered. Its still fast as fuck. No visible damage. Smells a bit wet inside and the engine took a big gulp but still runs fine gets up on transbrake fine and power skids the 255 pss as if they are solid plastic toy car tires.

[Mayuri Krab]

Originally Posted by 101Duck

Yeah no drama. I have a spare one already anyway. If not two.

Cool, how much shipped to WA?

[Socket]

Good luck with sale Duck
I'll def be interested

[E85 335]

how much for the intercooler

[Socket]

Ill take the ST stuff for $10K Duck

[iliketurtl3s]

no haggle!!!! go sockie

[EB89]

Originally Posted by Socket

Ill take the ST stuff for $10K Duck

There he is

[Socket]

Originally Posted by EB89

There he is

[Aus335iguy]

Awesome. On ya Socket!

[R32GOJIRA]

Originally Posted by Socket

Ill take the ST stuff for $10K Duck

Haha sick of waiting mate?

[MMM335]

if only it was tax time lol

[101Duck]

Haha Vaughn!

Sockets car will be a weapon, manual with ST! I'm excited.

So speaking to socket, I'm going to go to test and tune wednesday night coming. Try see if it holds together for one last shot at a 9 second pass. And then it's coming apart on thursday!

Also, pretty happy to keep the glide and shifter etc for a old holden project. So if anyone wants the glide adaptor and tailshaft and gearbox crossmember. I'll sell those bits seperate for $800
just incase anyone wants to slowly build their setup? martymil

[tawfeeqh]

Originally Posted by Socket

Ill take the ST stuff for $10K Duck

Nice one sock thats a lot of gear you getting for $10k can't wait to see it in flesh once its all bolted on

[MMM335]

socket ya should do me a good deal on a set of turbs now

glad to see this setup going to him but, not a car on here that is more deserving to rep it other then urs but duck lol

[Socket]

Originally Posted by tawfeeqh

Nice one sock thats a lot of gear you getting for $10k can't wait to see it in flesh once its all bolted on

Thanks mate will be a bit of work to get it all installed but will finally have it back on the road 👍