[Tambohamilton]

Maybe a silly question, but is there a way to default/factory code all modules in Protool? I can only see how to process individual modules.

EDIT: Confirmed by Protool support; this is not possible.

[Goboro100]

Originally Posted by Serf27

You can change the TCU vin with protools.

Hello is there a way to reset transmission characteristics? Shift memory?

[TunafishE93]

I think you can do it in xHP app without buying the tune, once app downloaded, three little bars on top left, diagnostic and you will see the reset adaption. Not sure if it works or if you can do the reset in Protool..

[Serf27]

Originally Posted by Goboro100

Hello is there a way to reset transmission characteristics? Shift memory?

You can reset transmission adaptions with protools but they not recommend it unless you have fully rebuilt the transmission.

[Josh_n52]

Originally Posted by Serf27

You can reset transmission adaptions with protools but they not recommend it unless you have fully rebuilt the transmission.

Yeah and don't Fuck wot your vo for fun ... Sometimes stupid 🤪 is too easy.

[ferocity02]

Can Protools be used to turn on the LPFP? Not just prime it, but actually turn it on and leave it running. I need to drain the fuel tank.

[ferocity02]

Originally Posted by ferocity02

Can Protools be used to turn on the LPFP? Not just prime it, but actually turn it on and leave it running. I need to drain the fuel tank.

I emailed them and confirmed that it can run the LPFP continuously by pressing the prime pump option and then not exiting the prompt in the app, so it continues to run.

[Sgop335]

Didnt know we had a Protool discussion here. Great tool and customer svc but i dont know what most of the functions do. What does reset ecu do?

[PJLux]

Should this thread be a Sticky? This is a popular tool.

[S65Hunter]

I'm sure this has been asked, but is there a way to code out the Amber corner lights using pro tool?

[Serf27]

Originally Posted by AlpineE93

I'm sure this has been asked, but is there a way to code out the Amber corner lights using pro tool?

Yes there is.

[S65Hunter]

I've got it to where its just the angel eyes as day time lights, but couldn't find how to completely disable amber lights (when the head lights are on)

[Dpc2u]

Been playing with the guages. The Protool app just keeps getting better. Did some coding on the M5 as well, euro mdm and some other things.

[jkline398]

I bought the diag and coding license and synced app, why does it say something about vehicle order not set, and when I try to create vehicle order I get a message that vehicle not connected, check ignition is ON... (I put key in and press startbutton, dash lights come on and a/c) I can't even read error codes, says not connected but I can turn on engine and get live data? 2010 e90 n54

[Serf27]

Try force closing the app and reconnecting.
Are you using a kdcan cable?

[lordnikon]

Sorry if this was already asked...does the Protool app require an internet connection (Wifi) to work?

[Serf27]

Originally Posted by lordnikon

Sorry if this was already asked...does the Protool app require an internet connection (Wifi) to work?

No it does not.

[lordnikon]

Is it possible to code the E90 rear fog lights to only illuminate one side, i.e. a single rear fog? (driver's side - left)

I assume the coding is in the Body Domain Module (BDM)?

I already have the euro switch installed.

[Serf27]

No it can’t.
You can remove the passenger side bulb and remove the bulb checks for the rear fog lights.

[bimmermech123]

Hello all, I recently installed the factory alarm hardware in my E90 and would like to activate the alarm via Protool. I have already done much coding to my E90, including angel eyes and folding mirrors. So my 2 questions are this:

1. Does anybody know whether the vehicle order $302 or +K302 will need to be added to activate the alarm (or both)?

2. Would I be able to make a backup of my CAS, FRM and KOMBI, modify the vehicle order (which would default these modules), and then upload the backups to the corresponding modules to retain the coding I have already done? I know this sounds like I'm being lazy, but I'd rather not have to code certain things like oil temperature again.

[Serf27]

Originally Posted by bimmermech123

Hello all, I recently installed the factory alarm hardware in my E90 and would like to activate the alarm via Protool. I have already done much coding to my E90, including angel eyes and folding mirrors. So my 2 questions are this:

1. Does anybody know whether the vehicle order $302 or +K302 will need to be added to activate the alarm (or both)?

2. Would I be able to make a backup of my CAS, FRM and KOMBI, modify the vehicle order (which would default these modules), and then upload the backups to the corresponding modules to retain the coding I have already done? I know this sounds like I'm being lazy, but I'd rather not have to code certain things like oil temperature again.

I have read that alarm coding is not needed for the red flashing light.
It would be best to code it.

A backup written over a default coded module with a new VO will erase the VO settings.
When the new VO is added, the module reverts to factory options and anything you’ve coded is gone.
When you write your back ups over the modules with new VOs, it will erase whatever options the new VO has, so no you cannot do that.

What you can do is look up what needs to be coded in each module and manually code it. Instead of clicking “save to CAS and FRM”, click no (or whatever the app says and manually code settings in each module for the alarm VO.

[Tambohamilton]

Originally Posted by Serf27

Instead of clicking “save to CAS and FRM”, click no (or whatever the app says and manually code settings in each module for the alarm VO.

You should still save the new VO to CAS and FRM, but not default code the modules if you want to code them manually. So click yes to save vo to both modules, but no to default code subsequent modules.