Alpina B3 Flash DIY with Winkfp

joe335in54 · 05-18-2014, 07:57 PM

Quote:

Originally Posted by bradsm87

I'm using NCS Expert 4.0.1 (Included in Standard Tools 2.12) and have tried many "Expert Mode" profiles provided by various people but I never get the "SG ausw" button after first selecting "Vin/ZCS/FA" on the first page. The third button along reads either "ZCS/FA f. ECU" or "ZCS aus SG" but never "SG ausw". When I press this button, it next has an option to choose chassis code then CAS but I do not want to take any chances unless somebody confirms for sure that this button is the exact same button with a different name. I've had too many scares with both my DME and TCU flashes to do anything unless I'm 100% sure!

Any help/confirmation would be greatly appreciated!

the older version of ncs expert show different abreviatons.. so its all the same with new or old ncs

1. you load profile
2.F1
3.F3
4.choose chassis (e89)
5.choose cas
6.Press back (f6)
7.choose ecu (module)
then at this point i belive you know what to do.. same process for older n newer Ncs software.

bradsm87 · 05-18-2014, 10:48 PM

Quote:

Originally Posted by joe335in54

the older version of ncs expert show different abreviatons.. so its all the same with new or old ncs

1. you load profile
2.F1
3.F3
4.choose chassis (e89)
5.choose cas
6.Press back (f6)
7.choose ecu (module)
then at this point i belive you know what to do.. same process for older n newer Ncs software.

So it's not possible for different profiles to assign different funtions to the same function key? (F1, F3 etc)?

bradsm87 · 05-19-2014, 03:56 AM

"ZCS aus SG" (German) or (ZCS/FA f. ECU) in NCS Expert 4.x do the same thing as "SG ausw" in NCS Expert 3.x. and I have successfully applied the paddle fix. Previous post edited.

PauloC · 06-05-2014, 09:15 PM

thanks a lot!

flash done!

Nickski · 07-01-2014, 09:33 PM

heres the error I get when I tried to program, any help would be appreciated.

[22:21:59.916] [2014-07-01] [<WinKFP Tool] 2089 PABD/CABD 06FLASH Programmieren 2538
[22:21:59.916] [2014-07-01] [<WinKFP Tool] switching programming mode failed 10FLASH, DIAGNOSE_MODE (ECUPM): ERROR_ECU_SECURITY_ACCESS_DENIED__SECURITY_ACCESS_ REQUESTED

[22:22:07.279] [2014-07-01] [<WinKFP Tool] 2089 PABD/CABD 06FLASH Programmieren 2812
[22:22:07.279] [2014-07-01] [<WinKFP Tool] switching programming mode failed 10FLASH, DIAGNOSE_MODE (ECUPM): ERROR_ECU_CONDITIONS_NOT_CORRECT_OR_REQUEST_SEQUEN CE_ERROR

[22:22:07.328] [2014-07-01] [<WinKFP Tool] 2089 Error COAPI2.CPP coapiRunCabd 6
[22:22:07.328] [2014-07-01] [<WinKFP Tool] switching programming mode failed SG_PROGRAMMIEREN

[22:22:07.329] [2014-07-01] [<WinKFP Tool] 2089 Error COAPIKF.CPP coapiKfProgSgD2 19
[22:22:07.329] [2014-07-01] [<WinKFP Tool] switching programming mode failed

cn555ic · 07-01-2014, 09:54 PM

Quote:

Originally Posted by Nickski

heres the error I get when I tried to program, any help would be appreciated.

[22:21:59.916] [2014-07-01] [<WinKFP Tool] 2089 PABD/CABD 06FLASH Programmieren 2538
[22:21:59.916] [2014-07-01] [<WinKFP Tool] switching programming mode failed 10FLASH, DIAGNOSE_MODE (ECUPM): ERROR_ECU_SECURITY_ACCESS_DENIED__SECURITY_ACCESS_ REQUESTED

[22:22:07.279] [2014-07-01] [<WinKFP Tool] 2089 PABD/CABD 06FLASH Programmieren 2812
[22:22:07.279] [2014-07-01] [<WinKFP Tool] switching programming mode failed 10FLASH, DIAGNOSE_MODE (ECUPM): ERROR_ECU_CONDITIONS_NOT_CORRECT_OR_REQUEST_SEQUEN CE_ERROR

[22:22:07.328] [2014-07-01] [<WinKFP Tool] 2089 Error COAPI2.CPP coapiRunCabd 6
[22:22:07.328] [2014-07-01] [<WinKFP Tool] switching programming mode failed SG_PROGRAMMIEREN

[22:22:07.329] [2014-07-01] [<WinKFP Tool] 2089 Error COAPIKF.CPP coapiKfProgSgD2 19
[22:22:07.329] [2014-07-01] [<WinKFP Tool] switching programming mode failed

Your configurations are not correct...Check the comports are set correctly and the latency must be set to 1

Nickski · 07-01-2014, 10:05 PM

Quote:

Originally Posted by cn555ic

Your configurations are not correct...Check the comports are set correctly and the latency must be set to 1

thanks!

setting in device manager set to com1
latency set to 1
obd.ini

Port=Com1
Hardware=USB
RETRY=ON
;Tracelevel=0xFFFFFFFF
;Tracelevel=0xFFFFFFFF
;Tracelevel=0xF0000000
;Tracelevel=0x0000FFFF
; Bit 0 = Funktionsaufruf
; Bit 1 = io Ergebnis
; Bit 2 = nio Ergebnis
; Bit 3 = Detailinfos
; Nibble 0 = readchar_wait
; Nibble 1 = main
; Nibble 2 = cmd
; Nibble 3 = obd
; Nibble 4 = send_and_receive_...
; Nibble 5 = read_telegram_...
; Nibble 6 = send_telegram
; Nibble 7 = SendData

EDIABAS.ini

Interface =STD:OBD
Simulation = 0

EcuPath =C:\EDIABAS\ECU
SimulationPath =C:\EDIABAS\SIM
TracePath =C:\EDIABAS\TRACE
TraceSize = 1024

let me know if you need more info, or if you see something wrong.

im opening winkfp form the extraced folder, not from a shortcut to my C drive. where is the executable winkfp?

thanks a lot!

Thanks much!

deeLow · 07-02-2014, 04:51 AM

I think I asked this before but I forget. Can I do this flash using Daten 50.2???

***checked previous posts, I guess I can. Also did test run in winkfp and found the numbers as posted in first post. So I just want to confirm one last time before I connect to my car that I will be A OK????

cn555ic · 07-02-2014, 07:37 AM

Quote:

Originally Posted by Nickski

thanks!

setting in device manager set to com1
latency set to 1
obd.ini

Port=Com1
Hardware=USB
RETRY=ON
;Tracelevel=0xFFFFFFFF
;Tracelevel=0xFFFFFFFF
;Tracelevel=0xF0000000
;Tracelevel=0x0000FFFF
; Bit 0 = Funktionsaufruf
; Bit 1 = io Ergebnis
; Bit 2 = nio Ergebnis
; Bit 3 = Detailinfos
; Nibble 0 = readchar_wait
; Nibble 1 = main
; Nibble 2 = cmd
; Nibble 3 = obd
; Nibble 4 = send_and_receive_...
; Nibble 5 = read_telegram_...
; Nibble 6 = send_telegram
; Nibble 7 = SendData

EDIABAS.ini

Interface =STD:OBD
Simulation = 0

EcuPath =C:\EDIABAS\ECU
SimulationPath =C:\EDIABAS\SIM
TracePath =C:\EDIABAS\TRACE
TraceSize = 1024

let me know if you need more info, or if you see something wrong.

im opening winkfp form the extraced folder, not from a shortcut to my C drive. where is the executable winkfp?

thanks a lot!

Thanks much!

it should be in ec-apps/nFS folder the winkfp

To be honest it doesnt really seem you have done enough research to even do this flash...I would read some more before diving into this.

deeLow · 07-02-2014, 02:08 PM

Just tried it and got this error when I hit program

Clueless from here

deeLow · 07-02-2014, 02:14 PM

@cn555ic

*disregard. I figured it out and it's Currently flashing as I type this

Nickski · 07-02-2014, 08:10 PM

Quote:

Originally Posted by Nickski

heres the error I get when I tried to program, any help would be appreciated.

[22:21:59.916] [2014-07-01] [<WinKFP Tool] 2089 PABD/CABD 06FLASH Programmieren 2538
[22:21:59.916] [2014-07-01] [<WinKFP Tool] switching programming mode failed 10FLASH, DIAGNOSE_MODE (ECUPM): ERROR_ECU_SECURITY_ACCESS_DENIED__SECURITY_ACCESS_ REQUESTED

[22:22:07.279] [2014-07-01] [<WinKFP Tool] 2089 PABD/CABD 06FLASH Programmieren 2812
[22:22:07.279] [2014-07-01] [<WinKFP Tool] switching programming mode failed 10FLASH, DIAGNOSE_MODE (ECUPM): ERROR_ECU_CONDITIONS_NOT_CORRECT_OR_REQUEST_SEQUEN CE_ERROR

[22:22:07.328] [2014-07-01] [<WinKFP Tool] 2089 Error COAPI2.CPP coapiRunCabd 6
[22:22:07.328] [2014-07-01] [<WinKFP Tool] switching programming mode failed SG_PROGRAMMIEREN

[22:22:07.329] [2014-07-01] [<WinKFP Tool] 2089 Error COAPIKF.CPP coapiKfProgSgD2 19
[22:22:07.329] [2014-07-01] [<WinKFP Tool] switching programming mode failed

just in-case someone else stumbles upon this with the same problem.
Check your settings, in device manager, set com port to 1 and latency to 1. check your ediabase.ini is set to Interface =STD:OBD
check your obd.ini is set to Port=Com1
Hardware=USB

then reboot. I had all those setting correct and the cable was communicating through IPNA. The reboot fixed it. the alpina b3 flash is the titties! thanks for the write up!

E93_335i · 07-04-2014, 01:25 PM

Hi guys I'm from capetown south africa, we got no coding guys this side of the world. Would anyone help me remote log in for the alpina tune please

cn555ic · 07-22-2014, 07:23 PM

Updated first post with Alpina Spdaten 53.0. Again this is not the full version of Spdaten 53.0 but a condensed file for strictly alpina flashing

WickedB · 07-25-2014, 01:16 PM

Any way to check the trans model to confirm if this will work or not?

ferocity02 · 07-28-2014, 12:44 PM

When importing the SPdaten 53.0 into Winkfp, it was asking me if I wanted to overwrite the existing files in the folders. Is that okay? There must have been a couple hundred files I had to overwrite.

cn555ic · 07-28-2014, 06:53 PM

Quote:

Originally Posted by ferocity02

When importing the SPdaten 53.0 into Winkfp, it was asking me if I wanted to overwrite the existing files in the folders. Is that okay? There must have been a couple hundred files I had to overwrite.

yes overwrite them

ferocity02 · 07-28-2014, 08:15 PM

When I try to update ZUSB and click on GKE215 I get this error message. Any idea what it means?

wildcatcrazy · 07-29-2014, 03:23 AM

Quote:

Originally Posted by ferocity02

When I try to update ZUSB and click on GKE215 I get this error message. Any idea what it means?

What is your manufactured date? If it's before 03/07, you're SOL.

ferocity02 · 07-29-2014, 11:08 AM

Quote:

Originally Posted by wildcatcrazy

What is your manufactured date? If it's before 03/07, you're SOL.

It's 4/4/2007 according to the VIN. But I do think that mine was made with old parts, none of the coding programs can talk with the car.

Is that what the error means?

wildcatcrazy · 07-29-2014, 12:23 PM

Quote:

Originally Posted by ferocity02

Quote:

Originally Posted by wildcatcrazy

What is your manufactured date? If it's before 03/07, you're SOL.

It's 4/4/2007 according to the VIN. But I do think that mine was made with old parts, none of the coding programs can talk with the car.

Is that what the error means?

With your updated DATENs, you should be good to go. Sorry, I have no idea...

ferocity02 · 07-29-2014, 12:32 PM

Quote:

Originally Posted by wildcatcrazy

With your updated DATENs, you should be good to go. Sorry, I have no idea...

I used BMW Coding Pack which included v49 of SP-daten for E8X, which I think covers E90. But I did download the v53 daten for this flash from the first post and imported it into Winkp as explained in the PDF.

I suspect I need to review my software/cable setup.

05-19-2014, 03:56 AM	#179
bradsm87 Lieutenant Colonel 595 Rep 1,693 Posts Drives: F25 LCI xDrive30d Join Date: Jun 2013 Location: Australia iTrader: (0)	"ZCS aus SG" (German) or (ZCS/FA f. ECU) in NCS Expert 4.x do the same thing as "SG ausw" in NCS Expert 3.x. and I have successfully applied the paddle fix. Previous post edited.
	Appreciate 0 Quote

06-05-2014, 09:15 PM	#180
PauloC New Member 0 Rep 11 Posts Drives: BMW Sedan 335i M 2008 Join Date: May 2013 Location: Mexico iTrader: (0)	thanks thanks a lot! flash done!
	Appreciate 0 Quote

07-01-2014, 09:33 PM	#181
Nickski New Member 0 Rep 10 Posts Drives: 2011 335xi Join Date: Jun 2014 Location: boston iTrader: (0)	error trying to program heres the error I get when I tried to program, any help would be appreciated. [22:21:59.916] [2014-07-01] [<WinKFP Tool] 2089 PABD/CABD 06FLASH Programmieren 2538 [22:21:59.916] [2014-07-01] [<WinKFP Tool] switching programming mode failed 10FLASH, DIAGNOSE_MODE (ECUPM): ERROR_ECU_SECURITY_ACCESS_DENIED__SECURITY_ACCESS_ REQUESTED [22:22:07.279] [2014-07-01] [<WinKFP Tool] 2089 PABD/CABD 06FLASH Programmieren 2812 [22:22:07.279] [2014-07-01] [<WinKFP Tool] switching programming mode failed 10FLASH, DIAGNOSE_MODE (ECUPM): ERROR_ECU_CONDITIONS_NOT_CORRECT_OR_REQUEST_SEQUEN CE_ERROR [22:22:07.328] [2014-07-01] [<WinKFP Tool] 2089 Error COAPI2.CPP coapiRunCabd 6 [22:22:07.328] [2014-07-01] [<WinKFP Tool] switching programming mode failed SG_PROGRAMMIEREN [22:22:07.329] [2014-07-01] [<WinKFP Tool] 2089 Error COAPIKF.CPP coapiKfProgSgD2 19 [22:22:07.329] [2014-07-01] [<WinKFP Tool] switching programming mode failed
	Appreciate 0 Quote

07-02-2014, 04:51 AM	#184
deeLow DOPE 148 Rep 758 Posts Drives: F80 Join Date: Jan 2014 Location: Earth iTrader: (2)	I think I asked this before but I forget. Can I do this flash using Daten 50.2??? ***checked previous posts, I guess I can. Also did test run in winkfp and found the numbers as posted in first post. So I just want to confirm one last time before I connect to my car that I will be A OK????
	Appreciate 0 Quote

07-02-2014, 02:08 PM	#186
deeLow DOPE 148 Rep 758 Posts Drives: F80 Join Date: Jan 2014 Location: Earth iTrader: (2)	Just tried it and got this error when I hit program Clueless from here Attached Images
	Appreciate 0 Quote

07-02-2014, 02:14 PM	#187
deeLow DOPE 148 Rep 758 Posts Drives: F80 Join Date: Jan 2014 Location: Earth iTrader: (2)	@cn555ic *disregard. I figured it out and it's Currently flashing as I type this
	Appreciate 0 Quote

07-04-2014, 01:25 PM	#189
E93_335i Registered 0 Rep 1 Posts Drives: E93 335i Join Date: Jul 2014 Location: South Africa iTrader: (0)	Bmw coding Hi guys I'm from capetown south africa, we got no coding guys this side of the world. Would anyone help me remote log in for the alpina tune please
	Appreciate 0 Quote

07-22-2014, 07:23 PM	#190
cn555ic 441 Rep 18,331 Posts Drives: 335i Join Date: Jun 2007 Location: US iTrader: (6)	Updated first post with Alpina Spdaten 53.0. Again this is not the full version of Spdaten 53.0 but a condensed file for strictly alpina flashing
	Appreciate 0 Quote

07-25-2014, 01:16 PM	#191
WickedB Second Lieutenant 15 Rep 290 Posts Drives: 2007 335i Convertible Join Date: Mar 2012 Location: Detroit, MI iTrader: (0)	Any way to check the trans model to confirm if this will work or not?
	Appreciate 0 Quote

07-28-2014, 12:44 PM	#192
ferocity02 Colonel 530 Rep 2,083 Posts Drives: 2013 135is Join Date: May 2014 Location: USA iTrader: (8)	When importing the SPdaten 53.0 into Winkfp, it was asking me if I wanted to overwrite the existing files in the folders. Is that okay? There must have been a couple hundred files I had to overwrite.
	Appreciate 0 Quote

07-28-2014, 08:15 PM	#194
ferocity02 Colonel 530 Rep 2,083 Posts Drives: 2013 135is Join Date: May 2014 Location: USA iTrader: (8)	When I try to update ZUSB and click on GKE215 I get this error message. Any idea what it means?
	Appreciate 0 Quote