[naamanf]

Originally Posted by topcat87

question: suppose i successfully did the Video-in-motion code, wil the internet broswer work when the vehicle is in motion as well?

How do you plan on getting the browser to work?

[rockblock]

Originally Posted by Neutrino45

This is the best person to order your cable from!

Originally Posted by justa3series
This seller is very repped, and also comes with adapter allowing working on all cars without soldering pins in cable.

http://cgi.ebay.com/ebaymotors/ws/eB...m=200599686350
This is the best person to order your cable from!

What's the difference between these 2 cables:

http://cgi.ebay.com/ebaymotors/ws/eB...m=160633214829 ($119)

http://cgi.ebay.com/ebaymotors/ws/eB...m=250839830539 ($59)

They're both made in China and seem to have the same features:

- Connects to USB (built in 1,5m long USB Cable, creates virtual comport)
- Double K-Line support (See Screenshot)
- High Speed D-CAN and PT-CAN support (500 kbit/s)
- Low Speed PT-CAN support (100 kbit/s)
- Battery voltage detection by control line (See Screenshot)
- Ignition voltage detection by control line

but the first one is 2x more expensive !! I have a 2010 e90 LCI

or this one, for $80 (gives free shipping) that also comes with software:
http://cgi.ebay.com/ebaymotors/ws/eB...=STRK:MEWAX:IT

[Neutrino45]

Not all cables are created equal. Just buy the one the we're recommending. It's the one that most of us are using and have not had any problems with it. It also comes w/ an adapter for pin8.

Here is the link to the latest active action from the same seller:
http://cgi.ebay.com/ebaymotors/BMW-I...item2eb4ac4cce

This is their home page:
http://www.one-stop-electronics.com/shop/

[mrtanz]

Anyone got a confirmed source with the latest daten files

[topcat87]

Originally Posted by naamanf

How do you plan on getting the browser to work?

dont really understand what u meant...

the internet broswer screen also gets blocked by a similar safety message when playing dvd's on the go

[rockblock]

Originally Posted by Neutrino45

Not all cables are created equal. Just buy the one the we're recommending. It's the one that most of us are using and have not had any problems with it. It also comes w/ an adapter for pin8.

Here is the link to the latest active action from the same seller:
http://cgi.ebay.com/ebaymotors/BMW-I...item2eb4ac4cce

This is their home page:
http://www.one-stop-electronics.com/shop/

OK thx....I was just curious as to why one cable is 2x more expensive than the other, given the specs are the same and electronic components are all made in China... maybe I'm too cheap, but $120 for a cable/interface seems a bit high to me - I'll check with the seller that you recommend and see if I can get a better deal...Thx for your input

[DESI4life10]

Originally Posted by rockblock

OK thx....I was just curious as to why one cable is 2x more expensive than the other, given the specs are the same and electronic components are all made in China... maybe I'm too cheap, but $120 for a cable/interface seems a bit high to me - I'll check with the seller that you recommend and see if I can get a better deal...Thx for your input

It may look the same, but the chips used inside makes the difference sometimes.

You can bargain that seller down to about $90ish. Plus if you have any issues with the cable, their customer service is top notch (Been through it )

[Elliott@DetailAddict]

Exactly. Don't be cheap up front. It's a lot more expensive to replace you're cas or cluster down the line...

[E92Ghost]

Has anyone already found the speed limit?

I've found below. I'm not sure if this is the speed limit. And do not know what value you should use to disable the speed limit.

LIMIT_M_DREHZAHL
wert_01
wert_03
wert_04
wert_06
wert_99
wert_101
wert_102
wert_103
wert_104
wert_105
wert_08
wert_09
wert_106
wert_14
wert_23
wert_24
wert_25
wert_26
wert_107
wert_108
wert_109
wert_110
wert_111
wert_112

[Elliott@DetailAddict]

Don't think thats a speed delimiter bud.
Thats most likely pulled from the KOMBI or CCC/CIC right?
It's most likely associated with the speed limit reminded you can set (where it shows "LIMIT" after a user defined speed and I think it beeps too)

The speed limiter is located in the DME not something we can code.

[rockblock]

Originally Posted by DESI4life10

You can bargain that seller down to about $90ish. Plus if you have any issues with the cable, their customer service is top notch (Been through it )

OK, I managed to get it for $90....I don't feel so bad now
Thx

[CasperSYTFU]

Originally Posted by DESI4life10

It may look the same, but the chips used inside makes the difference sometimes.

You can bargain that seller down to about $90ish. Plus if you have any issues with the cable, their customer service is top notch (Been through it )

Desi, do you know how to extend t˙e 1 touch signals to 4 or 7 blinks from 3?

[DESI4life10]

Originally Posted by CasperSYTFU

Desi, do you know how to extend t˙e 1 touch signals to 4 or 7 blinks from 3?

I don't know the exact line, but I know for sure it can be coded (cause another local member did it). I will look into it as well.

[Chewy734]

Originally Posted by CasperSYTFU

Desi, do you know how to extend t˙e 1 touch signals to 4 or 7 blinks from 3?

It takes you that long to switch lanes?

[E92Ghost]

Originally Posted by Grant@DetailAddict

Don't think thats a speed delimiter bud.
Thats most likely pulled from the KOMBI or CCC/CIC right?
It's most likely associated with the speed limit reminded you can set (where it shows "LIMIT" after a user defined speed and I think it beeps too)

The speed limiter is located in the DME not something we can code.

Thanks, you could be right that it is the speed limit reminded. And if it is not possible to code by us I don’t have to look further......

[Najt]

Hi, I am a newbie I have the e90 325D 2007/09... i have bought this cable:

http://cgi.ebay.co.uk/ws/eBayISAPI.d...=STRK:MEWNX:IT

when i start inpaloader the light of ignition and baterry is ON - is it normal?
I can access only few control units... but not the engine :-(
it shows me error : identification error

i have this cable - it seems to me that there should be more pin soldered , shouldnt they?

[justa3series]

With changing the turn signals it needs to be done via nettodat coding. The problem I am having is 4 items share same bytes so I don't know how to evaluate which one to change.

[E92Ghost]

I want to use the front blikers as DRL. I have them already on when the light are on. I found a value DRL_TFL_MIT_BLK_V_GED. But it is not on any module. May I add this value to the FRM module? I think the module FRM, because all other values of DRL are on FRM.

[Elliott@DetailAddict]

Originally Posted by Chewy734

It takes you that long to switch lanes?

lol just like having it signal a little longer to let the idiots next to me that I'm coming!

[Pseudo Nim]

Originally Posted by justa3series

With changing the turn signals it needs to be done via nettodat coding. The problem I am having is 4 items share same bytes so I don't know how to evaluate which one to change.

looking forward to hearing if you figure it out. i'd like more than three blinks, people ARE stupid :P

[DESI4life10]

Yea the nettodat will probably be the spot to change it (you won't be able to customize it on the kombi like you currently can with 1 or 3 blink)

[HaZe_X]

Originally Posted by rockblock

OK, I managed to get it for $90....I don't feel so bad now
Thx

Yeah was just was gonna say he will accept an offer for $90, he accepted my offer for that 2 days ago...