E90Post
 


Extreme Powerhouse
 
BMW 3-Series (E90 E92) Forum > BMW E90/E92/E93 3-series General Forums > General E90 Sedan / E91 Wagon / E92 Coupe / E93 Cabrio > What did you do to your car today?



Reply
 
Thread Tools Search this Thread
      03-26-2020, 03:32 PM   #11397
drtmvr
New Member
5
Rep
25
Posts

Drives: 2011 328i SULEV
Join Date: Nov 2018
Location: Las Vegas

iTrader: (0)

Quote:
Originally Posted by bobbby View Post
Took the car in for oil change, intercooler install, and to fix a leaky washer. Found out that my washer fluid line and coolant line were chewed by rodents...
Not a fan of cats, but you need a cat
Appreciate 0
      03-26-2020, 06:13 PM   #11398
SCHWARZ_E92
Second Lieutenant
SCHWARZ_E92's Avatar
United_States
238
Rep
265
Posts

Drives: 2009 BMW 335i
Join Date: Mar 2018
Location: Georgia

iTrader: (0)

Tried tracking down and fixing 2C6A 02 sensor mix up code. Found out one of the last owners wired in a downpipe fix and wired it all ghetto. Feel like one of the last owners put the car back to stock and then saw their wiring job and went "im not messing with that" then sold it
Appreciate 0
      03-26-2020, 09:56 PM   #11399
Vulcan50
Lieutenant
147
Rep
483
Posts

Drives: e92 335i
Join Date: Mar 2017
Location: Peoria, IL

iTrader: (0)

Quote:
Originally Posted by mweisdorfer View Post
Nice! What are you putting them on?
07 e92 335i they will be accompanying m3 suspension bits and 18x9" square fitment!
Appreciate 0
      03-26-2020, 10:40 PM   #11400
213e90n51
Lieutenant
213e90n51's Avatar
South Georgia and South Sandwich Islands
130
Rep
464
Posts

Drives: 2009 BMW 328i, Honda Civic Hat
Join Date: Mar 2020
Location: Los Angeles

iTrader: (0)

Garage List
2009 328i  [0.00]
2019 M4  [0.00]
2019 Honda Civic Ha ...  [0.00]
Anyone do any donuts or drifting with their e90s yet ?
Appreciate 0
      03-27-2020, 12:40 PM   #11401
nsjames
Brigadier General
1356
Rep
3,090
Posts

Drives: 08 328xi Touring
Join Date: May 2017
Location: ohio

iTrader: (0)

Quote:
Originally Posted by Barrique91 View Post
After trying to pry open the headlight with a heat gun, pry tools, flatheads, etc I realized that I should just cut it. I suppose it's easier with an oven but that's not an option for me. I cut the headlight with a Dremel, I just followed a line on the headlight that is right next to the permaseal. This leaves me with a small thin piece of plastic in the permaseal channel. I haven't gotten to taking this out yet(busy painting and doing some wiring). An approach I might try is to run a thin wire under the seal and "floss" it away to cut through all of it. I can update you once I do it. Keep in mind I am getting new lenses, so maybe this method might not be for you.
I've never had success using the oven to open a headlamp. By the time you get it out and to the workbench it's already lost 40-50 degrees of temp.

Using wire maybe, I've cut windshields free using the same technique. I imagine the sealant is pretty similar. Some urethane joint.

I'll have to pull that thing out of the parts room and take a real go at it.

I would like to put new lenses on both of mine, as they are crazing on the inside, so buffing isn't getting them as clear and crisp as I'd like them to be.

Did you find OE equivalent lenses somewhere?
Appreciate 0
      03-27-2020, 12:45 PM   #11402
Barrique91
First Lieutenant
Barrique91's Avatar
350
Rep
307
Posts

Drives: 2006 325xi Touring 6MT
Join Date: Apr 2018
Location: Idaho, USA

iTrader: (0)

Garage List
2006 BMW 325xi  [0.00]
Quote:
Originally Posted by nsjames View Post
Quote:
Originally Posted by Barrique91 View Post
After trying to pry open the headlight with a heat gun, pry tools, flatheads, etc I realized that I should just cut it. I suppose it's easier with an oven but that's not an option for me. I cut the headlight with a Dremel, I just followed a line on the headlight that is right next to the permaseal. This leaves me with a small thin piece of plastic in the permaseal channel. I haven't gotten to taking this out yet(busy painting and doing some wiring). An approach I might try is to run a thin wire under the seal and "floss" it away to cut through all of it. I can update you once I do it. Keep in mind I am getting new lenses, so maybe this method might not be for you.
I've never had success using the oven to open a headlamp. By the time you get it out and to the workbench it's already lost 40-50 degrees of temp.

Using wire maybe, I've cut windshields free using the same technique. I imagine the sealant is pretty similar. Some urethane joint.

I'll have to pull that thing out of the parts room and take a real go at it.

I would like to put new lenses on both of mine, as they are crazing on the inside, so buffing isn't getting them as clear and crisp as I'd like them to be.

Did you find OE equivalent lenses somewhere?
I think I found them. I don't understand why lenses would cost $130+ from vendors __ when they are just plastic. I found a seller on ali express that says they are for xenons and the photo has the screws for angel eyes. I will find out for sure how well they fit in the next week or two I think. Shipping takes a while. There's quite a bit of them on ali express you just have to search for the ones that specifically say xenon. I figured I rather "risk" buying $35 lenses than expensive ones that are probably the exact same thing. If they fit well i can send you a link to the exact same seller in the future. I don't want to lead someone in the wrong direction.
__________________
325xi Touring - 6MT - Sport Package
Appreciate 0
      03-27-2020, 02:17 PM   #11403
nsjames
Brigadier General
1356
Rep
3,090
Posts

Drives: 08 328xi Touring
Join Date: May 2017
Location: ohio

iTrader: (0)

Quote:
Originally Posted by Barrique91 View Post
I think I found them. I don't understand why lenses would cost $130+ from vendors __ when they are just plastic. I found a seller on ali express that says they are for xenons and the photo has the screws for angel eyes. I will find out for sure how well they fit in the next week or two I think. Shipping takes a while. There's quite a bit of them on ali express you just have to search for the ones that specifically say xenon. I figured I rather "risk" buying $35 lenses than expensive ones that are probably the exact same thing. If they fit well i can send you a link to the exact same seller in the future. I don't want to lead someone in the wrong direction.
well do update, and if they're not trash I'd like the link for sure.

no sense in putting nasty lenses back on.
I have a feeling this means I'm about to do headlamp things.

wheels first though.
Appreciate 1
      03-27-2020, 03:10 PM   #11404
Kbudz94
Private
Canada
2
Rep
70
Posts

Drives: BMW 335i
Join Date: Oct 2019
Location: Kingston Ontario

iTrader: (0)

https://datazap.me/u/northernn54/maj...ng-corrections found out I need to fix some major timing corrections. Think my LPFP might be dying. Need help please PM
Appreciate 0
      03-27-2020, 06:13 PM   #11405
mweisdorfer
Major General
mweisdorfer's Avatar
United_States
1372
Rep
5,830
Posts

Drives: 2007 Black/Black 335i e90
Join Date: Apr 2011
Location: Holly, MI

iTrader: (0)

Garage List
2007 BMW E90 335i  [0.00]
2008 bmw x5  [0.00]
Quote:
Originally Posted by Kbudz94 View Post
https://datazap.me/u/northernn54/maj...ng-corrections found out I need to fix some major timing corrections. Think my LPFP might be dying. Need help please PM
Replace your LPFS with the updated version. It's only $30.00 at FCP. It's best to ensure the data you are getting is accurate. If then, replace the LPFP. It's $170 or so at FCP. No big deal. Fuel pressure should be 65 or so at WOT. 74 even 84 at idol or just cruising around. If your pressure is in the 50's or lower at WOT, it's time for a change to a new or better than new LPFP.
Appreciate 0
      03-27-2020, 07:42 PM   #11406
ki_soarer
Second Lieutenant
127
Rep
279
Posts

Drives: 2010 335D
Join Date: May 2018
Location: MD

iTrader: (1)

I finally got around to installing my rear F30 BMW performance brakes.
Attached Images
 
Appreciate 1
NYBulldog943.00

      03-28-2020, 03:39 AM   #11407
535iM_Spadez
New Member
21
Rep
21
Posts

Drives: 2015 535i m-sport
Join Date: Mar 2020
Location: Florida

iTrader: (0)

Started the red tails , with translucent red paint.... also tried my hand at blending in the back bumper
Attached Images
 
Appreciate 0
      03-28-2020, 09:47 AM   #11408
535iM_Spadez
New Member
21
Rep
21
Posts

Drives: 2015 535i m-sport
Join Date: Mar 2020
Location: Florida

iTrader: (0)

Welp here it is ... never mind the tape lines 🥺
Attached Images
 
Appreciate 0
      03-28-2020, 10:11 AM   #11409
feuer
Major General
feuer's Avatar
United_States
3263
Rep
7,705
Posts

Drives: wife crazy!
Join Date: Apr 2015
Location: Chicago, IL

iTrader: (5)

Quote:
Originally Posted by RealJ22 View Post
No, it's this cheap one from Amazon. This company makes several.
So is taped? You didn't stitched together?
Appreciate 0
      03-28-2020, 12:28 PM   #11410
nsjames
Brigadier General
1356
Rep
3,090
Posts

Drives: 08 328xi Touring
Join Date: May 2017
Location: ohio

iTrader: (0)

Quote:
Originally Posted by 535iM_Spadez View Post
Started the red tails , with translucent red paint.... also tried my hand at blending in the back bumper
I admire your effort here, but in the future it's way easier to remove them for paint.
same goes with anything that's just screwed/taped to the body. If you can take it off it's easier to mask and paint.

final results turned out good.

wheel stupidity continues, but at least I'm on the easy and rewarding side of the curve.


my start/stop button was sad.


ebay five dollar holler isn't perfect, but better than 12 year old one.
Appreciate 0
      03-28-2020, 12:31 PM   #11411
535iM_Spadez
New Member
21
Rep
21
Posts

Drives: 2015 535i m-sport
Join Date: Mar 2020
Location: Florida

iTrader: (0)

Quote:
Originally Posted by nsjames View Post
Quote:
Originally Posted by 535iM_Spadez View Post
Started the red tails , with translucent red paint.... also tried my hand at blending in the back bumper
I admire your effort here, but in the future it's way easier to remove them for paint.
same goes with anything that's just screwed/taped to the body. If you can take it off it's easier to mask and paint.

final results turned out good.

wheel stupidity continues, but at least I'm on the easy and rewarding side of the curve.


my start/stop button was sad.


ebay five dollar holler isn't perfect, but better than 12 year old one.
I was going the lazy route but ... at the same time I had to do something , I appreciate the feedback ... and thank you on the results ... the rear bumper is a much better result from what it was originally 😩😩😆
Appreciate 0
      03-28-2020, 12:47 PM   #11412
nsjames
Brigadier General
1356
Rep
3,090
Posts

Drives: 08 328xi Touring
Join Date: May 2017
Location: ohio

iTrader: (0)

Quote:
Originally Posted by 535iM_Spadez View Post
I was going the lazy route but ... at the same time I had to do something , I appreciate the feedback ... and thank you on the results ... the rear bumper is a much better result from what it was originally 😩😩😆
I have found that the lazy route often takes more time and effort than just doing it properly.

go slow to work fast is something that has taken me many years to understand.
Appreciate 0
      03-28-2020, 12:54 PM   #11413
mweisdorfer
Major General
mweisdorfer's Avatar
United_States
1372
Rep
5,830
Posts

Drives: 2007 Black/Black 335i e90
Join Date: Apr 2011
Location: Holly, MI

iTrader: (0)

Garage List
2007 BMW E90 335i  [0.00]
2008 bmw x5  [0.00]
Quote:
Originally Posted by 535iM_Spadez View Post
Quote:
Originally Posted by nsjames View Post
Quote:
Originally Posted by 535iM_Spadez View Post
Started the red tails , with translucent red paint.... also tried my hand at blending in the back bumper
I admire your effort here, but in the future it's way easier to remove them for paint.
same goes with anything that's just screwed/taped to the body. If you can take it off it's easier to mask and paint.

final results turned out good.

wheel stupidity continues, but at least I'm on the easy and rewarding side of the curve.


my start/stop button was sad.


ebay five dollar holler isn't perfect, but better than 12 year old one.
I was going the lazy route but ... at the same time I had to do something , I appreciate the feedback ... and thank you on the results ... the rear bumper is a much better result from what it was originally 😩😩😆
You need a red one with that silver trim !
Appreciate 0
      03-28-2020, 01:16 PM   #11414
nsjames
Brigadier General
1356
Rep
3,090
Posts

Drives: 08 328xi Touring
Join Date: May 2017
Location: ohio

iTrader: (0)

Quote:
Originally Posted by mweisdorfer View Post
You need a red one with that silver trim !
[james may] that's casual[/james may]

I couldn't take a red button everyday.
hell, I've stripped just about everything out of my cluster.


the less "busy" the interior is the happier I am.

I don't even really care for how glossy this one is, but it's better than the one that's leaking light where it's all worn through.
Appreciate 0
      03-28-2020, 05:04 PM   #11415
Serf27
Captain
Serf27's Avatar
United_States
217
Rep
673
Posts

Drives: E90 335i
Join Date: Apr 2018
Location: High Desert, CA

iTrader: (0)

Quote:
Originally Posted by 535iM_Spadez View Post
Welp here it is ... never mind the tape lines 🥺
Nice.
Clean up the over spray on the trunk and it will look better.
__________________
E90 335i 383WHP/433TQ.
E70 X5 35i M Sport Package.
E91 328XIT M Sport Package.
E91 328XIT—E60 N54 6 speed MT.
Appreciate 0
      03-28-2020, 05:05 PM   #11416
Serf27
Captain
Serf27's Avatar
United_States
217
Rep
673
Posts

Drives: E90 335i
Join Date: Apr 2018
Location: High Desert, CA

iTrader: (0)

Red start button with red m button to match. (Not pictured)
Attached Images
 
__________________
E90 335i 383WHP/433TQ.
E70 X5 35i M Sport Package.
E91 328XIT M Sport Package.
E91 328XIT—E60 N54 6 speed MT.
Appreciate 0
      03-28-2020, 05:11 PM   #11417
535iM_Spadez
New Member
21
Rep
21
Posts

Drives: 2015 535i m-sport
Join Date: Mar 2020
Location: Florida

iTrader: (0)

For $150 with a new y-pipe 2.50" tip ...deleted the resonator and muffler
Attached Images
    
Appreciate 0
      03-28-2020, 06:11 PM   #11418
Boosted12a
Private First Class
55
Rep
186
Posts

Drives: BMW 335i x
Join Date: Jun 2019
Location: Va

iTrader: (0)

Didn't do anything but ordered some koni yellows for the rear, new lower mounts and Polly upper mounts. One of my rears are leaking and I need to get my inspection done by end of April. I'll get some yellows for the front in a month or two and some dinan springs after that.
Appreciate 0
Reply

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -5. The time now is 10:04 AM.




e90post
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2020, vBulletin Solutions Inc.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST