E90Post
 


TNT Racewerks
 
BMW 3-Series (E90 E92) Forum > E90 / E92 / E93 3-series Powertrain and Drivetrain Discussions > N54 Turbo Engine / Drivetrain / Exhaust Modifications - 335i > Removing Insert Nut from Driveshaft



Reply
 
Thread Tools Search this Thread
      01-19-2022, 07:25 PM   #1
CamJam
New Member
5
Rep
11
Posts

Drives: 2007 335i
Join Date: Jan 2022
Location: Arizona, USA

iTrader: (0)

Removing Insert Nut from Driveshaft

I'm in the process of replacing my CSB and giubo, and have managed (with much difficulty) to start removing the insert nut with a 50mm thin wrench. It seems that as the insert nut (green arrow) is loosening, this black metal ring (red arrow) is deforming. Thought I'd better stop and ask advice before I bugger something up. Is the nut supposed to fit inside the ring as you back it off, or how does that work? Seems like the driveshaft should move forward as the nut is loosened, but I think the giubo (which I've read should be removed after the insert nut) will be providing some resistance. Any advice on how to proceed would be much appreciated.

Geez, this nut is stubborn. I'm wondering if heating it up with a heat gun would melt the loctite enough to make it easier?

EDIT: I see from the Bentley manual that this black ring is a retaining clip, but there are no instructions on how to remove it. I assume that it must not be a continuous ring if you're able to remove it, but I'm not seeing any break in the metal anywhere. Any hints? Looks more like an oil seal to me, but none of the diagrams I have show one at that location.
Attached Images
 

Last edited by CamJam; 01-20-2022 at 11:20 AM..
Appreciate 0
      01-20-2022, 06:03 AM   #2
iqraceworks
Brigadier General
iqraceworks's Avatar
1981
Rep
3,715
Posts

Drives: 2007 335i
Join Date: Aug 2019
Location: Missouri

iTrader: (0)

Have you searched online? I've seen lots of videos and forums posts talking about removing the driveshaft..... although I don't remember what they said about that ring.

Following.....
Appreciate 0
      01-20-2022, 11:04 AM   #3
CamJam
New Member
5
Rep
11
Posts

Drives: 2007 335i
Join Date: Jan 2022
Location: Arizona, USA

iTrader: (0)

Thanks for the response. None of the videos I've found show the driveshaft with the big nut on the end, which I believe might only be used on the turbo models. Within that, there appear to variations, as the insert nut kit has been revised a couple times. Perhaps I'll have a better understanding when my new parts arrive here later today.
Appreciate 0
      01-20-2022, 11:38 AM   #4
infinite_creations25
Private First Class
56
Rep
117
Posts

Drives: bmw
Join Date: Jan 2017
Location: garage

iTrader: (0)

I replaced my differential last summer and that nut was indeed an absolute pain to get off. The factory loctite will fight you the entire way until the nut is completely off. As you turn the nut, the driveshaft will begin pushing back towards the front of the car and the nut will remain on the diff. As for the black ring, It’s a retaining clip for the nut and not an oil seal. The new nut will come with a new one so doesn’t matter if you damage it. It simply pops off with a screwdriver.

Last edited by infinite_creations25; 01-20-2022 at 11:51 AM..
Appreciate 0
      01-20-2022, 12:08 PM   #5
CamJam
New Member
5
Rep
11
Posts

Drives: 2007 335i
Join Date: Jan 2022
Location: Arizona, USA

iTrader: (0)

Great news! Thanks for that bit of info, IC25!!
Appreciate 0
      01-20-2022, 08:25 PM   #6
CamJam
New Member
5
Rep
11
Posts

Drives: 2007 335i
Join Date: Jan 2022
Location: Arizona, USA

iTrader: (0)

Thought I'd pass along to anyone else that needs to do this that this $29 wrench set on E-Bay includes the wrench you need to get insert nut off. It's made of 1/4" plate steel. I questioned whether it would be stout enough, but it was. I used a long handled 1/2" drive ratchet with a short extension. The other wrench in the set is useless for this, but maybe you can use it on your ATV.

https://www.ebay.com/itm/232699396780

Probably doesn't work quite as well as the $300(!) German one, but it got the job done for me.
Appreciate 0
      01-21-2022, 08:28 AM   #7
iqraceworks
Brigadier General
iqraceworks's Avatar
1981
Rep
3,715
Posts

Drives: 2007 335i
Join Date: Aug 2019
Location: Missouri

iTrader: (0)

FYI....you can also get a set of large metric open end wrenches (including 50mm) from Harbor Freight for around $60.
Appreciate 0
      01-22-2022, 07:18 PM   #8
CamJam
New Member
5
Rep
11
Posts

Drives: 2007 335i
Join Date: Jan 2022
Location: Arizona, USA

iTrader: (0)

Quote:
Originally Posted by iqraceworks View Post
FYI....you can also get a set of large metric open end wrenches (including 50mm) from Harbor Freight for around $60.
I did consider that, but it looked like the HF wrench was a tad too thick and would require grinding down to fit. What I did get at HF though was a Bearing Separator and Puller Set (#62593) for $50. It made short work of removing the CSB from the driveshaft.

BTW, the new insert nut is a whole lot easier to put on than it was to get the old one off. I guess it takes 15 minutes or so for the thread sealant to kick in.
Appreciate 0
Reply

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -5. The time now is 12:57 PM.




e90post
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST