|
|
|
|
|
|
BMW Garage | BMW Meets | Register | Today's Posts | Search |
|
BMW 3-Series (E90 E92) Forum
>
Is this headlight wiring diagram accurate?
|
|
02-16-2008, 02:13 AM | #1 |
Tired
131
Rep 2,673
Posts |
Is this headlight wiring diagram accurate?
I found this in a different thread made by another member, and I am wondering if it's accurate for an 08' e90.
I need to tap the highbeam wire for the "Flash2Pass" system, and if this is correct it will save a shitload of time. Anyone have a shop manual handy? Anyone tapped the highlight beam wire before? Any help is appreciated.
__________________
BMW-less
|
02-16-2008, 02:21 AM | #2 |
Captain
20
Rep 650
Posts |
That diagram is correct for my car which is an 07. Not sure if they changed anything but I don't see why they would have. You should be fine. You could always test that pin with a test light to see.
__________________
"it remains the benchmark by which all competitors, including Lexus, must be measured."
|
Appreciate
0
|
02-16-2008, 10:16 AM | #3 |
Major General
108
Rep 8,327
Posts |
I used it for corner delete mod and it was all correct on my 07 as well
__________________
Legal Disclaimer: Anything I or anyone else says about my vehicle on this website(e90post.com or any affiliated or nonaffiliated sites), pertaining to modifications, is only to gain acceptance from my/our peers, and does not actually represent anything actually existing on my car, and thus, cannot be held against me in any issues, i.e. warranty claims, that may arise.
|
Appreciate
0
|
02-16-2008, 10:51 AM | #4 |
Tired
131
Rep 2,673
Posts |
Thanks guys.
I'm at work w/o the car in front of me, but looking at that schematic, does the pic represent one looking at the front or the back of the molex?
__________________
BMW-less
|
Appreciate
0
|
02-16-2008, 12:59 PM | #5 |
Major General
108
Rep 8,327
Posts |
when you see the car you will see there is only 1 way it can be, from the front you cant see anything. It is from the inside of the engine bay, looking toward the front bumper.
__________________
Legal Disclaimer: Anything I or anyone else says about my vehicle on this website(e90post.com or any affiliated or nonaffiliated sites), pertaining to modifications, is only to gain acceptance from my/our peers, and does not actually represent anything actually existing on my car, and thus, cannot be held against me in any issues, i.e. warranty claims, that may arise.
|
Appreciate
0
|
02-16-2008, 01:09 PM | #6 | |
Tired
131
Rep 2,673
Posts |
Quote:
But my question is, looking at the diagram above, does that diagram represent looking at the plug from the front (where it connects to the light), or looking at it from the back, where the harness from the car enters the plug?
__________________
BMW-less
|
|
Appreciate
0
|
02-16-2008, 01:15 PM | #7 |
Major General
108
Rep 8,327
Posts |
oh, from the back, by the harness. There is one little plastic cover piece. When you remove it, it is obvious that is what the diagram is describing.
__________________
Legal Disclaimer: Anything I or anyone else says about my vehicle on this website(e90post.com or any affiliated or nonaffiliated sites), pertaining to modifications, is only to gain acceptance from my/our peers, and does not actually represent anything actually existing on my car, and thus, cannot be held against me in any issues, i.e. warranty claims, that may arise.
|
Appreciate
0
|
02-16-2008, 01:26 PM | #8 |
Tired
131
Rep 2,673
Posts |
Got it, thanks again. I can do the install now on the Flass2Pass in like 5 minutes lol.
__________________
BMW-less
|
Appreciate
0
|
02-16-2008, 03:42 PM | #9 |
Major General
108
Rep 8,327
Posts |
What are you trying to activate when you put your high beams on? A little led light on the front bumper that will say in reverse, GO AHEAD
__________________
Legal Disclaimer: Anything I or anyone else says about my vehicle on this website(e90post.com or any affiliated or nonaffiliated sites), pertaining to modifications, is only to gain acceptance from my/our peers, and does not actually represent anything actually existing on my car, and thus, cannot be held against me in any issues, i.e. warranty claims, that may arise.
|
Appreciate
0
|
02-25-2008, 03:35 PM | #10 |
Registered
0
Rep 2
Posts |
I have tried to install a Flash2Pass using this diagram on my 08 335 na dit failed. I alternately used both the ground (2 and 4) but no success.
I powered the transmitter through the battery and that workesd, so there is nothing wrong with the transmitter. If anyone has an accurate wiring diagram, please post it Thanks |
Appreciate
0
|
02-25-2008, 06:06 PM | #11 | |
Tired
131
Rep 2,673
Posts |
Quote:
__________________
BMW-less
|
|
Appreciate
0
|
02-25-2008, 06:34 PM | #12 |
Brigadier General
218
Rep 4,726
Posts |
I'm not sure, but if it is you just saved me a TON of time.
I do see something wrong with it though (but I have an e92) #5 is the angel eyes for me. But to help out, you can figure out the orientation because the positive wires will be yellow and the grounds black. Of the main wires that is. might help in some way too. Where did you get that by the way, is there an e92 one in the same place?
__________________
Last edited by O-cha; 02-28-2008 at 10:53 PM.. |
Appreciate
0
|
02-25-2008, 07:24 PM | #13 |
Major
85
Rep 1,104
Posts |
i used the diagram for resistor installation...works perfectly
O-Cha i think e92 has a different diagram...im not sure edit: diagram is from e90 corner delete diy theres a e92 corner delete mod thread u might wanna check out - http://www.e90post.com/forums/showth...dlight+diagram
__________________
2007 E90 335i JB
2010 E90 M3 JRB |
Appreciate
0
|
02-25-2008, 08:03 PM | #14 | |
Brigadier General
218
Rep 4,726
Posts |
Quote:
__________________
|
|
Appreciate
0
|
02-28-2008, 03:24 PM | #16 |
Tired
131
Rep 2,673
Posts |
e90 or e92?
__________________
BMW-less
|
Appreciate
0
|
Bookmarks |
|
|