BMW E90 MASK-GW softWare update

ste821 · 08-28-2015, 11:41 AM

Hi Friend,
I was start Programming E90. programming was going good. but after few minute fail MASK-GW (professional radio) Fiberoptic also dead. Now i am trying to update by WINKFP. but cannot update.

Can anybody help me about Radio module , How to update software.? i cannot replace it. because BMW parts very few in our country. mainly kind radio.

Before Programming it was perfectly work and run. After Programming dead.

Plz need adv about update software.

thanks
Sanjib

Sensible_ · 08-28-2015, 03:09 PM

Go to realoem and find alternative zusb number to flash with then manually choose it in winkfp.

Although if it's ECU problem because of failed flash you are in trouble.

Maybe NFS emergency flash can help. Be careful with it and research this:

http://www.e90post.com/forums/showthread.php?t=849434

matteblue3er · 08-28-2015, 04:14 PM

You should not even be attempting to flash a head unit with a DCAN cable.

Only ICOM!

Your only hope is NFS.

ste821 · 08-28-2015, 04:42 PM

Quote:

Originally Posted by Sensible_

Go to realoem and find alternative zusb number to flash with then manually choose it in winkfp.

Although if it's ECU problem because of failed flash you are in trouble.

Maybe NFS emergency flash can help. Be careful with it and research this:

http://www.e90post.com/forums/showthread.php?t=849434

is it possible to help me vmware ? i have icom NFS all and update 2015. but i am not used NFS. if possible plz email me. your skype or others

my email: ste821@gmail.com

sanjib

Sensible_ · 08-29-2015, 02:03 AM

Watch the video in the link I gave you. It's simple.

ste821 · 08-29-2015, 02:18 PM

Quote:

Originally Posted by Sensible_

Watch the video in the link I gave you. It's simple.

i give you two PDF report ISTA/P. i cannot understand how to find CD73 (MASK-GW) ecu Address.

Plz help me to find ECU Address and ZUSB number. INPA not communication
with cd73 Audio (MASK-gw). so cannot understand how to find it. plz need your help.

thanks
sanjib

Sensible_ · 08-29-2015, 07:39 PM

ECU address is shown your winkfp - comfort mode selects it. I see in your screen shot its: 62

To be sure, check inpa - do error / fault code scan and results will show you ECU address.

e.g. JBBF is address 00

Model: E89X
Scope: all control module
JobStatus: OKAY
Quantity: 18
-----------------------------------------------------------------
ADR Gen. name JobStatus
92 VIRTSG92 ERROR_ECU_SERVICE_NOT_SUPPORTED
-----------------------------------------------------------------
ADR Gen. name JobStatus Number of errors
Error code Kind of error
00 JBBF OKAY No Error stored
01 MRS OKAY No Error stored
12 DME/DDE OKAY 2 Error stored
4222 44
4242 44
17 EKP OKAY No Error stored
29 DSC OKAY No Error stored
36 TEL/MULF OKAY No Error stored
3C CDC OKAY No Error stored
40 CAS OKAY No Error stored
41 DWA OKAY No Error stored
50 SINE OKAY No Error stored
56 FZD OKAY No Error stored
60 KOMBI OKAY No Error stored
62 MOSTGW OKAY No Error stored
63 MASK/CCC OKAY No Error stored
64 PDC OKAY No Error stored
72 FRM OKAY No Error stored
78 KLIMA OKAY No Error stored

Paste your INPA log here so we can see what modules you have. I guess you have RAD2 with built in MOST-GW.

ste821 · 08-30-2015, 08:38 AM

Quote:

Originally Posted by Sensible_

ECU address is shown your winkfp - comfort mode selects it. I see in your screen shot its: 62

To be sure, check inpa - do error / fault code scan and results will show you ECU address.

e.g. JBBF is address 00

Model: E89X
Scope: all control module
JobStatus: OKAY
Quantity: 18
-----------------------------------------------------------------
ADR Gen. name JobStatus
92 VIRTSG92 ERROR_ECU_SERVICE_NOT_SUPPORTED
-----------------------------------------------------------------
ADR Gen. name JobStatus Number of errors
Error code Kind of error
00 JBBF OKAY No Error stored
01 MRS OKAY No Error stored
12 DME/DDE OKAY 2 Error stored
4222 44
4242 44
17 EKP OKAY No Error stored
29 DSC OKAY No Error stored
36 TEL/MULF OKAY No Error stored
3C CDC OKAY No Error stored
40 CAS OKAY No Error stored
41 DWA OKAY No Error stored
50 SINE OKAY No Error stored
56 FZD OKAY No Error stored
60 KOMBI OKAY No Error stored
62 MOSTGW OKAY No Error stored
63 MASK/CCC OKAY No Error stored
64 PDC OKAY No Error stored
72 FRM OKAY No Error stored
78 KLIMA OKAY No Error stored

Paste your INPA log here so we can see what modules you have. I guess you have RAD2 with built in MOST-GW.

NFS Error log. below.

[05:02:51.119] [2015-11-15] [--] 1020 Error COAPIKF.CPP coapiKfInit 31
[05:02:51.119] [2015-11-15] [--] File could not be opened for reading info.eng

================================================== ==============================
[05:03:43.099] [2015-11-15] [<WinKFP Tool] 7015 PABD/CABD RA2CL2 Ident 1282
[05:03:43.099] [2015-11-15] [<WinKFP Tool] ECU adresses are set - no answer from ECU an gateway (IFH-0009), no OPPS/Most 10FLASH, IDENT: IFH-0009: No response from controlunit

[05:04:03.098] [2015-11-15] [<WinKFP Tool] 7015 Error COAPI2.CPP coapiRunCabd 6
[05:04:03.098] [2015-11-15] [<WinKFP Tool] ECU adresses are set - no answer from ECU an gateway (IFH-0009), no OPPS/Most SG_IDENT_LESEN

[05:04:03.098] [2015-11-15] [<WinKFP Tool] 7015 Error COAPIKF.CPP coapiKfGetHwNrFromSgD2 3
[05:04:03.098] [2015-11-15] [<WinKFP Tool] ECU adresses are set - no answer from ECU an gateway (IFH-0009), no OPPS/Most

================================================== ==============================(19)

thanks
sanjib

Sensible_ · 08-30-2015, 02:40 PM

Did you try NFS?

I meant post Error Memory from INPA.

ste821 · 08-31-2015, 03:50 PM

Quote:

Originally Posted by Sensible_

Did you try NFS?

I meant post Error Memory from INPA.

no NFS output.

if i select easyconnect with AUTO Async. than.

but when i select OBD by easyconnect then output
new photo.

plz advise

thank
sanjib

matteblue3er · 08-31-2015, 04:30 PM

IFH-009 is a com error.

You either have a bad cable, corrupt driver, incorrect com port settings, incorrect interface setting in the EDIABAS.ini file, or lack of an emulator if you are using an ICOM head.

ste821 · 08-31-2015, 06:03 PM

Quote:

Originally Posted by matteblue3er

IFH-009 is a com error.

You either have a bad cable, corrupt driver, incorrect com port settings, incorrect interface setting in the EDIABAS.ini file, or lack of an emulator if you are using an ICOM head.

i am using clone ICOM with MOST CONNECTOR

Sanjib

ste821 · 09-01-2015, 05:26 PM

can anybody edit my both INI file.

When i program with 6801 then OK. but i need with MOST and connect with 6802. when easy connect config with MOST then not work. only OBD (6801) oK.

i post here my two INI files. I need ICOM + MOST both config for CCC unit programming.

thanks
sanjib

Sensible_ · 09-02-2015, 02:59 AM

It's simple. MOST channel require REMOTE.ini configuration like this:

Code:

;#### Remote.ini Musterdatei für OPPS Firmware Version kleiner 625 ####


[Base]
ek_info = Einfacher Betrieb im Automatik - Router Modus
RemoteHost=169.254.33.45
port = 6801
InitCmd0 = FE 04 00 85
DisconnectOnApiEnd = 1


[DiagBus]
ek_info = Mehrfachbetrieb: Nutzt nur K-Line, gibt MOST frei
RemoteHost=169.254.33.45
port = 6801
InitCmd0 = FE 05 00 80 05
DisconnectOnApiEnd = 1


[MOST]
ek_info = Mehrfachbetrieb: Nutzt MOST, gibt K-Line frei
RemoteHost=169.254.33.45
port = 6802
InitCmd0 = FE 05 00 80 01
DisconnectOnApiEnd = 1


[MOST_CTRL]
ek_info = Mehrfachbetrieb: Nutzt MOST, Asynchronkanal gesperrt, gibt K-Line frei
RemoteHost=169.254.33.45
port =6802
InitCmd0 = FE 05 00 80 01
;Asynchron ausschalten
InitCmd1 = FD 05 00 03 00
DisconnectOnApiEnd = 1


[MOST_ASYNC]
ek_info = Mehrfachbetrieb: Nutzt MOST mit Asynchronkanal, gibt K-Line frei
RemoteHost=169.254.33.45
port =6802
InitCmd0 = FE 05 00 80 01
;Asynchron einschalten
InitCmd1 = FD 05 00 03 01
;Ab 190 Bytes Telegrammlängen Asynchronkanal benutzen
InitCmd2 = FD 06 00 97 BE 00
DisconnectOnApiEnd = 1


[AUTO_ASYNC]
ek_info = Einfachbetrieb mit automatischer Umschaltung K-Line / MOST, Kontroll / Asynchronkanal
RemoteHost=169.254.33.45
port = 6802
; Router auf MOST
InitCmd0 = FE 04 00 01 
;Asynchron einschalten
InitCmd1 = FD 05 00 03 01
;Ab 190 Bytes Telegrammlängen Asynchronkanal benutzen
InitCmd2 = FD 06 00 97 BE 00
; Router wieder auf Automatik
InitCmd3 = FE 04 00 00 
DisconnectOnApiEnd = 1


[MOST_MASTER]
ek_info = OPPS Most-Master und Clock-Master
RemoteHost=169.254.33.45
port = 6802
InitCmd0 = FE 04 00 01
InitCmd1 = FD 06 00 01 01 01
DisconnectOnApiEnd = 1


;#### Remote.ini Musterdatei für OPPS Firmware Version ab 625 ####


; Ab Firmware Version 625 ist das OBD Interface fest auf Port 6801 und das MOST Interface
; fest auf Port 6802. Parallelbetrieb sofort erlaubt. 
; Obacht! Router Kommandos sind ab dieser Version _verboten_ (Init CMDs mit FE am Anfang)


[OBD_ab625]
ek_info = OPPS Betrieb mit OBD Interface, also K-Line oder D-CAN
RemoteHost=169.254.33.45
;Dieser Port hat _immer_ das OBD Interface, also K-Line oder D-CAN
port = 6801


[MOST_CTRL_ab625]
ek_info = OPPS Betrieb mit MOST Interface, Asynchronkanal gesperrt
RemoteHost = 169.254.33.45
; Dieser Port hat _immer_ das MOST Interface
port = 6802
; Asynchronkanal sperren
InitCmd0= FD 05 00 03 00 


[MOST_ASYNC_ab625]
ek_info = OPPS Betrieb mit MOST Interface, Asynchronkanal erlaubt
RemoteHost = 169.254.33.45
; Dieser Port hat _immer_ das MOST Interface
port =6802
; Asynchronkanal erlauben 
InitCmd0= FD 05 00 03 01
; ab 0 Bytes Asynchronkanal benutzen
InitCmd1= FD 06 00 97 00 00 
; Bei Steuergeräten, die den Asynchronkanal nicht unterstützen, 
; und bei Telegrammen Mit SID != 0x36 wird automatisch der Kontrollkanal verwendet


[MOST_MASTER_ab625]
ek_info = OPPS Most-Master und Clock-Master
RemoteHost=169.254.33.45
port =6802
InitCmd0 = FD 06 00 01 01 01
DisconnectOnApiEnd = 1

You need to define MOST in EDIABAS.ini

Like :

Interface = REMOTE:name in EDIABAS.ini
e.g.
Interface = REMOTE:MOST # for using MOST
Interface = REMOTEiagBus # for DiagBus

That's all you need in EDIABAS.ini
Don't specify host and port as they are already defined in REMOTE.ini

This enables single single channel, to switch you need to restart or use something like:

[AUTO_ASYNC]
ek_info = Einfachbetrieb mit automatischer Umschaltung K-Line / MOST, Kontroll / Asynchronkanal
RemoteHost=opps_name
port = 6802
; Router auf MOST
InitCmd0 = FE 04 00 01
;Asynchron einschalten
InitCmd1 = FD 05 00 03 01
;Ab 190 Bytes Telegrammlängen Asynchronkanal benutzen
InitCmd2 = FD 06 00 97 BE 00
; Router wieder auf Automatik
InitCmd3 = FE 04 00 00
DisconnectOnApiEnd = 1

matteblue3er · 09-02-2015, 03:15 PM

Search for and download "Ediabas Konfiguator"

ste821 · 09-04-2015, 03:59 PM

Quote:

Originally Posted by Sensible_

It's simple. MOST channel require REMOTE.ini configuration like this:

Code:

;#### Remote.ini Musterdatei für OPPS Firmware Version kleiner 625 ####


[Base]
ek_info = Einfacher Betrieb im Automatik - Router Modus
RemoteHost=169.254.33.45
port = 6801
InitCmd0 = FE 04 00 85
DisconnectOnApiEnd = 1


[DiagBus]
ek_info = Mehrfachbetrieb: Nutzt nur K-Line, gibt MOST frei
RemoteHost=169.254.33.45
port = 6801
InitCmd0 = FE 05 00 80 05
DisconnectOnApiEnd = 1


[MOST]
ek_info = Mehrfachbetrieb: Nutzt MOST, gibt K-Line frei
RemoteHost=169.254.33.45
port = 6802
InitCmd0 = FE 05 00 80 01
DisconnectOnApiEnd = 1


[MOST_CTRL]
ek_info = Mehrfachbetrieb: Nutzt MOST, Asynchronkanal gesperrt, gibt K-Line frei
RemoteHost=169.254.33.45
port =6802
InitCmd0 = FE 05 00 80 01
;Asynchron ausschalten
InitCmd1 = FD 05 00 03 00
DisconnectOnApiEnd = 1


[MOST_ASYNC]
ek_info = Mehrfachbetrieb: Nutzt MOST mit Asynchronkanal, gibt K-Line frei
RemoteHost=169.254.33.45
port =6802
InitCmd0 = FE 05 00 80 01
;Asynchron einschalten
InitCmd1 = FD 05 00 03 01
;Ab 190 Bytes Telegrammlängen Asynchronkanal benutzen
InitCmd2 = FD 06 00 97 BE 00
DisconnectOnApiEnd = 1


[AUTO_ASYNC]
ek_info = Einfachbetrieb mit automatischer Umschaltung K-Line / MOST, Kontroll / Asynchronkanal
RemoteHost=169.254.33.45
port = 6802
; Router auf MOST
InitCmd0 = FE 04 00 01 
;Asynchron einschalten
InitCmd1 = FD 05 00 03 01
;Ab 190 Bytes Telegrammlängen Asynchronkanal benutzen
InitCmd2 = FD 06 00 97 BE 00
; Router wieder auf Automatik
InitCmd3 = FE 04 00 00 
DisconnectOnApiEnd = 1


[MOST_MASTER]
ek_info = OPPS Most-Master und Clock-Master
RemoteHost=169.254.33.45
port = 6802
InitCmd0 = FE 04 00 01
InitCmd1 = FD 06 00 01 01 01
DisconnectOnApiEnd = 1


;#### Remote.ini Musterdatei für OPPS Firmware Version ab 625 ####


; Ab Firmware Version 625 ist das OBD Interface fest auf Port 6801 und das MOST Interface
; fest auf Port 6802. Parallelbetrieb sofort erlaubt. 
; Obacht! Router Kommandos sind ab dieser Version _verboten_ (Init CMDs mit FE am Anfang)


[OBD_ab625]
ek_info = OPPS Betrieb mit OBD Interface, also K-Line oder D-CAN
RemoteHost=169.254.33.45
;Dieser Port hat _immer_ das OBD Interface, also K-Line oder D-CAN
port = 6801


[MOST_CTRL_ab625]
ek_info = OPPS Betrieb mit MOST Interface, Asynchronkanal gesperrt
RemoteHost = 169.254.33.45
; Dieser Port hat _immer_ das MOST Interface
port = 6802
; Asynchronkanal sperren
InitCmd0= FD 05 00 03 00 


[MOST_ASYNC_ab625]
ek_info = OPPS Betrieb mit MOST Interface, Asynchronkanal erlaubt
RemoteHost = 169.254.33.45
; Dieser Port hat _immer_ das MOST Interface
port =6802
; Asynchronkanal erlauben 
InitCmd0= FD 05 00 03 01
; ab 0 Bytes Asynchronkanal benutzen
InitCmd1= FD 06 00 97 00 00 
; Bei Steuergeräten, die den Asynchronkanal nicht unterstützen, 
; und bei Telegrammen Mit SID != 0x36 wird automatisch der Kontrollkanal verwendet


[MOST_MASTER_ab625]
ek_info = OPPS Most-Master und Clock-Master
RemoteHost=169.254.33.45
port =6802
InitCmd0 = FD 06 00 01 01 01
DisconnectOnApiEnd = 1

You need to define MOST in EDIABAS.ini

Like :

Interface = REMOTE:name in EDIABAS.ini
e.g.
Interface = REMOTE:MOST # for using MOST
Interface = REMOTEiagBus # for DiagBus

That's all you need in EDIABAS.ini
Don't specify host and port as they are already defined in REMOTE.ini

This enables single single channel, to switch you need to restart or use something like:

[AUTO_ASYNC]
ek_info = Einfachbetrieb mit automatischer Umschaltung K-Line / MOST, Kontroll / Asynchronkanal
RemoteHost=opps_name
port = 6802
; Router auf MOST
InitCmd0 = FE 04 00 01
;Asynchron einschalten
InitCmd1 = FD 05 00 03 01
;Ab 190 Bytes Telegrammlängen Asynchronkanal benutzen
InitCmd2 = FD 06 00 97 BE 00
; Router wieder auf Automatik
InitCmd3 = FE 04 00 00
DisconnectOnApiEnd = 1

Today i connect ICOM with OBD. winkpf start program but fail. 2 -3 times try
but fails. error below.

================================================== ==============================
[07:48:00.356] [2015-11-20] [<WinKFP Tool] 2020 PABD/CABD 06FLASH ZifLesen 1184
[07:48:00.356] [2015-11-20] [<WinKFP Tool] ECU does not answer 10FLASH, ZIF_LESEN: ERROR_CHECK_PRGREF

[07:48:00.356] [2015-11-20] [<WinKFP Tool] 2020 Error COAPI2.CPP coapiRunCabd 6
[07:48:00.356] [2015-11-20] [<WinKFP Tool] ECU does not answer ZIF

[07:48:00.356] [2015-11-20] [<WinKFP Tool] 2020 Error COAPIKF.CPP coapiKfCheckReferenzD2 8
[07:48:00.356] [2015-11-20] [<WinKFP Tool] ECU does not answer ZIF lesen

[07:48:42.648] [2015-11-20] [<WinKFP Tool] 2082 PABD/CABD 06FLASH Programmieren 2935
[07:48:42.648] [2015-11-20] [<WinKFP Tool] Clear flash failed 10FLASH, FLASH_LOESCHEN (...): ERROR_ECU_ROUTINE_NOT_COMPLETE

[07:48:42.648] [2015-11-20] [<WinKFP Tool] 2082 PABD/CABD 06FLASH Programmieren 2947
[07:48:42.648] [2015-11-20] [<WinKFP Tool] Clear flash failed 10FLASH, FLASH_LOESCHEN (...)

[07:48:42.679] [2015-11-20] [<WinKFP Tool] 2082 Error COAPI2.CPP coapiRunCabd 6
[07:48:42.679] [2015-11-20] [<WinKFP Tool] Clear flash failed SG_PROGRAMMIEREN

[07:48:42.695] [2015-11-20] [<WinKFP Tool] 2082 Error COAPIKF.CPP coapiKfProgSgD2 19
[07:48:42.695] [2015-11-20] [<WinKFP Tool] Clear flash failed

thanks
sanjib

Sensible_ · 09-04-2015, 04:04 PM

And log from NFS?

ste821 · 09-04-2015, 04:54 PM

Quote:

Originally Posted by Sensible_

And log from NFS?

Yes
i try NFS and Winfpk both same. log

tnx
sanjib

Sensible_ · 09-04-2015, 05:34 PM

I suggest try different zusb number. What number are you using?

It's easy to find previous version. Maybe it will work.

It seems your ICOM is working correctly with winkfp now so it remains only bricked unit or problem with zusb (which I have seen although not with this exact error)

ste821 · 09-05-2015, 01:34 AM

Quote:

Originally Posted by Sensible_

I suggest try different zusb number. What number are you using?

It's easy to find previous version. Maybe it will work.

It seems your ICOM is working correctly with winkfp now so it remains only bricked unit or problem with zusb (which I have seen although not with this exact error)

i am using 9205947. address 0x62. can you help me to find ZUSB number?

My device info.

Model No: CD73
part No:65.12-6971703
HW: 6952294

sanjib

Sensible_ · 09-05-2015, 05:02 AM

So,

9205947 is for ECU family RA2SL2

This is correct yes?

Well, previous zb number was: 9199438

Look in RA2SL2.HIS you will see...

Sensible_ · 09-05-2015, 05:04 AM

For older, you must work back through daten in data folder and check the HIS files...

Sadly I don't have any other datens...

08-28-2015, 11:41 AM	#1
ste821 New Member 5 Rep 13 Posts Drives: Audi Join Date: Oct 2013 Location: Bangladesh iTrader: (0)	BMW E90 MASK-GW softWare update Hi Friend, I was start Programming E90. programming was going good. but after few minute fail MASK-GW (professional radio) Fiberoptic also dead. Now i am trying to update by WINKFP. but cannot update. Can anybody help me about Radio module , How to update software.? i cannot replace it. because BMW parts very few in our country. mainly kind radio. Before Programming it was perfectly work and run. After Programming dead. Plz need adv about update software. thanks Sanjib Attached Images
	Appreciate 0 Tweet Quote

08-28-2015, 03:09 PM	#2
Sensible_ Colonel 529 Rep 2,503 Posts Drives: 2008 E90 Join Date: Feb 2012 Location: London iTrader: (1)	Go to realoem and find alternative zusb number to flash with then manually choose it in winkfp. Although if it's ECU problem because of failed flash you are in trouble. Maybe NFS emergency flash can help. Be careful with it and research this: http://www.e90post.com/forums/showthread.php?t=849434
	Appreciate 0 Quote

08-28-2015, 04:14 PM	#3
matteblue3er Captain 238 Rep 947 Posts Drives: Racecar Join Date: Jul 2015 Location: Philly iTrader: (0)	You should not even be attempting to flash a head unit with a DCAN cable. Only ICOM! Your only hope is NFS.
	Appreciate 0 Quote

08-29-2015, 02:03 AM	#5
Sensible_ Colonel 529 Rep 2,503 Posts Drives: 2008 E90 Join Date: Feb 2012 Location: London iTrader: (1)	Watch the video in the link I gave you. It's simple.
	Appreciate 0 Quote

08-29-2015, 07:39 PM	#7
Sensible_ Colonel 529 Rep 2,503 Posts Drives: 2008 E90 Join Date: Feb 2012 Location: London iTrader: (1)	ECU address is shown your winkfp - comfort mode selects it. I see in your screen shot its: 62 To be sure, check inpa - do error / fault code scan and results will show you ECU address. e.g. JBBF is address 00 Model: E89X Scope: all control module JobStatus: OKAY Quantity: 18 ----------------------------------------------------------------- ADR Gen. name JobStatus 92 VIRTSG92 ERROR_ECU_SERVICE_NOT_SUPPORTED ----------------------------------------------------------------- ADR Gen. name JobStatus Number of errors Error code Kind of error 00 JBBF OKAY No Error stored 01 MRS OKAY No Error stored 12 DME/DDE OKAY 2 Error stored 4222 44 4242 44 17 EKP OKAY No Error stored 29 DSC OKAY No Error stored 36 TEL/MULF OKAY No Error stored 3C CDC OKAY No Error stored 40 CAS OKAY No Error stored 41 DWA OKAY No Error stored 50 SINE OKAY No Error stored 56 FZD OKAY No Error stored 60 KOMBI OKAY No Error stored 62 MOSTGW OKAY No Error stored 63 MASK/CCC OKAY No Error stored 64 PDC OKAY No Error stored 72 FRM OKAY No Error stored 78 KLIMA OKAY No Error stored Paste your INPA log here so we can see what modules you have. I guess you have RAD2 with built in MOST-GW. Last edited by Sensible_; 08-29-2015 at 07:50 PM..
	Appreciate 0 Quote

08-30-2015, 02:40 PM	#9
Sensible_ Colonel 529 Rep 2,503 Posts Drives: 2008 E90 Join Date: Feb 2012 Location: London iTrader: (1)	Did you try NFS? I meant post Error Memory from INPA.
	Appreciate 0 Quote

08-31-2015, 04:30 PM	#11
matteblue3er Captain 238 Rep 947 Posts Drives: Racecar Join Date: Jul 2015 Location: Philly iTrader: (0)	IFH-009 is a com error. You either have a bad cable, corrupt driver, incorrect com port settings, incorrect interface setting in the EDIABAS.ini file, or lack of an emulator if you are using an ICOM head.
	Appreciate 0 Quote

09-02-2015, 03:15 PM	#15
matteblue3er Captain 238 Rep 947 Posts Drives: Racecar Join Date: Jul 2015 Location: Philly iTrader: (0)	Search for and download "Ediabas Konfiguator"
	Appreciate 0 Quote

09-04-2015, 04:04 PM	#17
Sensible_ Colonel 529 Rep 2,503 Posts Drives: 2008 E90 Join Date: Feb 2012 Location: London iTrader: (1)	And log from NFS?
	Appreciate 0 Quote

09-04-2015, 05:34 PM	#19
Sensible_ Colonel 529 Rep 2,503 Posts Drives: 2008 E90 Join Date: Feb 2012 Location: London iTrader: (1)	I suggest try different zusb number. What number are you using? It's easy to find previous version. Maybe it will work. It seems your ICOM is working correctly with winkfp now so it remains only bricked unit or problem with zusb (which I have seen although not with this exact error)
	Appreciate 0 Quote

09-05-2015, 05:02 AM	#21
Sensible_ Colonel 529 Rep 2,503 Posts Drives: 2008 E90 Join Date: Feb 2012 Location: London iTrader: (1)	So, 9205947 is for ECU family RA2SL2 This is correct yes? Well, previous zb number was: 9199438 Look in RA2SL2.HIS you will see...
	Appreciate 0 Quote

09-05-2015, 05:04 AM	#22
Sensible_ Colonel 529 Rep 2,503 Posts Drives: 2008 E90 Join Date: Feb 2012 Location: London iTrader: (1)	For older, you must work back through daten in data folder and check the HIS files... Sadly I don't have any other datens...
	Appreciate 0 Quote